Details, datasheet, quote on part number: THS6032IVFP
PartTHS6032IVFP
CategoryAnalog & Mixed-Signal Processing => Amplifiers => High Speed/Video Amplifiers => Line Drivers and Receivers
TitleLine Drivers and Receivers
Descriptionti THS6032, Low-power Adsl Central Office Line Driver
CompanyTexas Instruments, Inc.
DatasheetDownload THS6032IVFP datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Central Office 1.35-W Total Power Dissipation for Full-Rate ADSL Into a 25- Load Low-Impedance Shutdown Mode Allows Reception of Incoming Signal During Standby Two Modes of Operation Class-G Mode: 4 Power Supplies, 1.35 W Power Dissipation Class-AB Mode: 2 Power Supplies, 2 W Power Dissipation Low Distortion THD = 62 dBc = 1 MHz, VO(PP) V, 25- Load THD = 69 dBc = 1 MHz, VO(PP) V, 25- Load 400-mA Minimum Output Current Into a 25- Load High Speed 65-MHz Bandwidth , 25- Load 100-MHz Bandwidth , 100- Load 1200 V/s Slew Rate Thermal Shutdown and Short Circuit Protection Evaluation Module Available

THERMALLY ENHANCED SOIC (DWP) PowerPAD PACKAGE (TOP VIEW)

NC Not Connected This terminal is internally connected to the thermal pad. MicroStar Junior (GQE) PACKAGE (TOP VIEW)

description

The is a low-power line driver ideal for asymmetrical digital subscriber line (ADSL) applications. This device contains two high-current, high-speed current-feedback drivers, which can be configured differentially for driving ADSL signals at the central office. The THS6032 features a unique class-G architecture to lower power consumption 1.35 W. The THS6032 can also be operated in a traditional class-AB mode to reduce the number of power supplies to two.

HIGH-SPEED xDSL LINE DRIVER/RECEIVER FAMILY DEVICE THS6072 THS7002 DRIVER RECEIVER 15 V DESCRIPTION 500-mA differential line driver and receiver 500-mA differential line driver 250-mA differential line driver 500-mA low-power ADSL central-office line driver Low-noise ADSL receiver Low-power ADSL receiver Low-noise programmable-gain ADSL receiver

CAUTION: The THS6032 provides ESD protection circuitry. However, permanent damage can still occur if this device is subjected to high-energy electrostatic discharges. Proper ESD precautions are recommended to avoid any performance degradation or loss of functionality. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD and MicroStar Junior are trademarks of Texas Instruments.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

The class-G architecture supplies current to the load from four supplies. For low output voltages (typically < +2.5), some of the output current is supplied from the +VCC(L) and VCC(L) supplies (typically 5 V). For large output voltages (typically 2.5 and + 2.5), the output current is supplied from +VCC(H) and VCC(H) (typically 15 V). This current sharing between VCC(L) and VCC(H) minimizes power dissipation within the THS6032 output stages for high crest factor ADSL signals. The THS6032 features a low-impedance shutdown mode, which allows the central office to receive incoming calls even after the device has been shut down. The THS6032 is available packaged in the patented PowerPAD package. This package provides outstanding thermal characteristics in a small-footprint surface-mount package, which is fully compatible with automated surface-mount assembly procedures. It is also available in the new MicroStar Junior BGA package. This package is only mm2 in area, allowing for high density PCB designs. Shutdown (SHDN1 and SHDN2) allows for powering down the internal circuitry for power conservation or for multiplexing. Separate shutdown controls are available for each channel on the THS6032. The control levels are TTL compatible. When turned off, each driver output is placed in a low impedance state which is determined by the voltage at DGND. This virtual ground at the outputs allows proper termination of a transmission line.

AVAILABLE OPTIONS PACKAGED DEVICES TA PowerPAD PLASTIC SMALL OUTLINE (DWP) THS6032CDWP MicroStar Junior BGA (GQE) THS6032CGQER PowerPAD TQFP (VFP) THS6032CVFP EVALUATION MODULES

to 85C The DWP packages are available taped and reeled. Add an R suffix to the device type (i.e.,THS6032CDWPR) The GQE packages are only available taped and reeled.

TERMINAL NAME 2IN 2IN+ VCCH VCCH+ VCCL VCCL+ SHDN1 SHDN2 DGND PAD NC DWP PACKAGE TERMINAL NO. GQE PACKAGE TERMINAL NO. J4 J7 N/A VFP PACKAGE TERMINAL NO. N/A

MicroStar Junior (GQE) PACKAGE (TOP VIEW)

NOTE: Shaded terminals are used for thermal connection to the ground plane. VFP PACKAGE (TOP VIEW)

 

Related products with the same datasheet
THS6032CDWPR
THS6032CGQER
THS6032CVFP
THS6032CVFPR
THS6032IDWP
THS6032IDWPR
THS6032IGQER
THS6032IVFPR
THS6032CDWPG4
THS6032CVFPG4
THS6032CVFPRG4
Some Part number from the same manufacture Texas Instruments, Inc.
THS6032IVFPR ti THS6032, Low-power Adsl Central Office Line Driver
THS6042
THS6042CD ti THS6042, 350-mA, +/-12V Adsl Cpe Line Driver
THS6043
THS6043CD ti THS6043, 350-mA, +/-12V Adsl Cpe Line Driver With Shutdown
THS6052
THS6052CD ti THS6052, 175-mA, +/-12V Adsl Cpe Line Driver
THS6053
THS6053CD ti THS6053, 175-mA, +/-12V Adsl Cpe Line Driver With Shutdown
THS6062 Low-noise Adsl Dual Differential Receiver
THS6062CD ti THS6062, Low-noise Adsl Dual Differential Receiver
THS6062D Low-noise Adsl Dual Differential Receiver
THS6062EVM
THS6062ID ti THS6062, Low-noise Adsl Dual Differential Receiver
THS6072 Low-power Adsl Differential Receiver
THS6072CD ti THS6072, Low-power Adsl Differential Receiver
THS6072D Low-power Adsl Differential Receiver
THS6072ID ti THS6072, Low-power Adsl Differential Receiver
THS6092
THS6092CD ti THS6092, 275-mA, +12V Adsl Cpe Line Driver
THS6093

CD74HCT4066E : Standard Bus Switches ti CD74HCT4066, High Speed CMOS Logic Quad Bilateral Switches

PT6913A : Plug-in Power Solutions->Non-Isolated->Single Nega ti PT6913, -1.5Vout 9W 5V-Input Adjustable Plus to Minus Voltage Converter

SNJ54BCT240J : Inverting Buffers and Drivers ti SN54BCT240, Octal Buffers/drivers With 3-State Outputs

TPS2104DBVR : Power MUXes ti TPS2104, 2.7-5.5V Dual In/single Out MOSFET, 0.5A Main/0.1A Aux Input, Act-low Enable, Industrial Temp.

TLV2772AMDRG4 : 2.7-v High-slew-rate Rail-to-rail Output DUAL Operational Amplifiers

DAC8164D : 14-bit, Quad Channel, Ultra-low Glitch, Voltage Output Digital-to-analog Converter with 2.5v, 2ppm/c Internal Reference

SN74AUP2G34YFPR : Logic - Buffers, Drivers, Receivers, Transceiver Integrated Circuit (ics) Buffer/Line Driver, Non-Inverting Tape & Reel (TR) 4mA, 4mA 0.8 V ~ 3.6 V; IC BUFF/DVR DUAL LP SC70-6 Specifications: Logic Type: Buffer/Line Driver, Non-Inverting ; Package / Case: 6-TSSOP, SC-88, SOT-363 ; Packaging: Tape & Reel (TR) ; Mounting Type: Surface Mount ; Number of Bits per Element: 1 ; Number of Elements: 2 ; Operating Temperature: -40C ~ 85C ; Voltage - Supply: 0.8 V ~ 3.6 V ; C

DS90C187LFE : LINE RECEIVER Specifications: Device Type: Receiver

 
0-C     D-L     M-R     S-Z