Details, datasheet, quote on part number: THS6032DWP
PartTHS6032DWP
CategoryCommunication => DSL (Digital Subscriber Line) => ADSL
DescriptionLow-power Adsl Central-office Line Driver
CompanyTexas Instruments, Inc.
DatasheetDownload THS6032DWP datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Central Office ­ 1.35-W Total Power Dissipation for Full-Rate ADSL Into a 25- Load Low-Impedance Shutdown Mode ­ Allows Reception of Incoming Signal During Standby Two Modes of Operation ­ Class-G Mode: 4 Power Supplies, 1.35 W Power Dissipation ­ Class-AB Mode: 2 Power Supplies, 2 W Power Dissipation Low Distortion ­ THD = ­62 dBc = 1 MHz, VO(PP) V, 25- Load ­ THD = ­69 dBc = 1 MHz, VO(PP) V, 25- Load 400-mA Minimum Output Current Into a 25- Load High Speed ­ 65-MHz Bandwidth , 25- Load ­ 100-MHz Bandwidth , 100- Load ­ 1200 V/µs Slew Rate Thermal Shutdown and Short Circuit Protection Evaluation Module Available

THERMALLY ENHANCED SOIC (DWP) PowerPADTM PACKAGE (TOP VIEW)

Cross section view showing PowerPAD This terminal is internally connected to the thermal pad. MicroStar JuniorTM (GQE) PACKAGE (TOP VIEW)

description

The is a low-power line driver ideal for asymmetrical digital subscriber line (ADSL) applications. This device contains two high-current, high-speed current-feedback drivers, which can be configured differentially for driving ADSL signals at the central office. The THS6032 features a unique class-G architecture to lower power consumption 1.35 W. The THS6032 can also be operated in a traditional class-AB mode to reduce the number of power supplies to two.

HIGH-SPEED xDSL LINE DRIVER/RECEIVER FAMILY DEVICE THS6072 THS7002 DRIVER RECEIVER ±15 V DESCRIPTION 500-mA differential line driver and receiver 500-mA differential line driver 250-mA differential line driver 500-mA low-power ADSL central-office line driver Low-noise ADSL receiver Low-power ADSL receiver Low-noise programmable-gain ADSL receiver

CAUTION: The THS6032 provides ESD protection circuitry. However, permanent damage can still occur if this device is subjected to high-energy electrostatic discharges. Proper ESD precautions are recommended to avoid any performance degradation or loss of functionality.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD and MicroStar Junior are trademarks of Texas Instruments.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

The class-G architecture supplies current to the load from four supplies. For low output voltages (typically < +2.5), some of the output current is supplied from the +VCC(L) and ­VCC(L) supplies (typically ± 5 V). For large output voltages (typically ­ 2.5 and + 2.5), the output current is supplied from +VCC(H) and ­VCC(H) (typically ± 15 V). This current sharing between VCC(L) and VCC(H) minimizes power dissipation within the THS6032 output stages for high crest factor ADSL signals. The THS6032 features a low-impedance shutdown mode, which allows the central office to receive incoming calls even after the device has been shut down. The THS6032 is available packaged in the patented PowerPAD package. This package provides outstanding thermal characteristics in a small-footprint surface-mount package, which is fully compatible with automated surface-mount assembly procedures. It is also available in the new MicoStar Junior BGA package. This package is only mm2 in area, allowing for high density PCB designs. Shutdown (SHDN1 and SHDN2) allows for powering down the internal circuitry for power conservation or for multiplexing. Separate shutdown controls are available for each channel on the THS6032. The control levels are TTL compatible. When turned off, each driver output is placed in a low impedance state which is determined by the voltage at DGND. This virtual ground at the outputs allows proper termination of a transmission line.

AVAILABLE OPTIONS PACKAGED DEVICES to 70°C PowerPAD PLASTIC SMALL OUTLINE (DWP) THS6032CDWP PACKAGED DEVICES MicroStar Junior (BGA) (GQE) THS6032CGQE EVALUATION MODULES THS6032EVM THS6032GQE EVM

to 85°C The THS6032 is available taped and reeled. Add an R suffix to the device type (i.e.,THS6032CDWPR) Uses the THS6032CGQE packaging option.

TERMINAL NAME 2IN­ 2IN+ VCCH­ VCCH+ VCCL­ VCCL+ SHDN1 SHDN2 DGND PAD NC DWP PACKAGE TERMINAL NO. GQE PACKAGE TERMINAL NO. J4 J7 N/A

MicroStar JuniorTM (GQE) PACKAGE (TOP VIEW)


NOTE: Shaded terminals are used for thermal connection to the ground plane.

 

Related products with the same datasheet
THS6032GQE
THS6032GQEEVM
THS6032IGQE
Some Part number from the same manufacture Texas Instruments, Inc.
THS6032EVM Low-power Adsl Central-office Line Driver
THS6032GQE
THS6032IDWP ti THS6032, Low-power Adsl Central Office Line Driver
THS6032IGQE Low-power Adsl Central-office Line Driver
THS6032IGQER ti THS6032, Low-power Adsl Central Office Line Driver
THS6042
THS6042CD ti THS6042, 350-mA, +/-12V Adsl Cpe Line Driver
THS6043
THS6043CD ti THS6043, 350-mA, +/-12V Adsl Cpe Line Driver With Shutdown
THS6052
THS6052CD ti THS6052, 175-mA, +/-12V Adsl Cpe Line Driver
THS6053
THS6053CD ti THS6053, 175-mA, +/-12V Adsl Cpe Line Driver With Shutdown
THS6062 Low-noise Adsl Dual Differential Receiver
THS6062CD ti THS6062, Low-noise Adsl Dual Differential Receiver
THS6062D Low-noise Adsl Dual Differential Receiver
THS6062EVM
THS6062ID ti THS6062, Low-noise Adsl Dual Differential Receiver
THS6072 Low-power Adsl Differential Receiver
THS6072CD ti THS6072, Low-power Adsl Differential Receiver
THS6072D Low-power Adsl Differential Receiver

PT5823A : Plug-in Power Solutions->Non-Isolated->Single Posi ti PT5823, 1.8V 16A, 12-V Input Adjustable Step-down Isr

SN54ABTH245FK : Octal Bus Transceivers With 3-state Outputs

SN74AUP1G80DBVR : Low-power Single Postitive-edge-triggered D-type Flip-flop

TMS370C036A : 8-bit Microcontroller

UC2901J : Feedback Signal Generators ti UC2901, ISOlated Feedback Generator

ADS8319IDRCR : Precision 16-Bit SAR W/ SPI Interface In MSOP-10 * 500-kHz Sample Rate * 16-Bit Resolution * Zero Latency at Full Speed * Unipolar, Single-Ended Input, Range: 0 V to Vref * SPI Compatible Serial Interface with Daisy Chain Option * Excellent Performance: o 93.6 dB

TL7705ACDRE4 : Supply-voltage Supervisors

LM3S1P51-IBZ80-C5 : Embedded - Microcontroller Integrated Circuit (ics) Internal Tray 1.08 V ~ 3.6 V; IC ARM CORTEX MCU 64KB 108NFBGA Specifications: Program Memory Size: 64KB (64K x 8) ; RAM Size: 24K x 8 ; Number of I /O: 67 ; Package / Case: 108-LFBGA ; Speed: 80MHz ; Oscillator Type: Internal ; Packaging: Tray ; Program Memory Type: FLASH ; EEPROM Size: - ; Core Processor: ARM® Cortex™-M3 ; Data Converters: A/D 16x10b ; Core S

TX253-30 : Obsolete/Discontinued Part Numbers 680X500 PIXEL IMAGE SENSOR -; 680X500 PIXEL IMAGE SENSOR Specifications: Lead Free Status: Contains Lead ; RoHS Status: RoHS Non-Compliant

 
0-C     D-L     M-R     S-Z