|Category||Semiconductors => Amplifiers => Operational Amplifiers (Op Amps) => High-Speed Op Amps (>=50MHz)|
|Part family||THS6032 Low-Power ADSL Central Office Line Driver|
|Description||Low-Power ADSL Central Office Line Driver 20-SO PowerPAD 0 to 70|
|Company||Texas Instruments, Inc.|
|Datasheet||Download THS6032 datasheet
|Cross ref.||Similar parts: AD8016ARB, AD8016ARB-EVAL, AD8016ARB-REEL, AD8016ARE-REEL, AD8016ARE-REEL7, AD8016XRB, AD8016XRB-IBIAS, LT1795IFE|
|Input Bias Current(Max)(pA)||9000000|
|Iq per channel(Max)(mA)||10.8|
|Total Supply Voltage(Max)(+5V=5, +/-5V=10)||32|
|Total Supply Voltage(Min)(+5V=5, +/-5V=10)||10|
|Approx. Price (US$)||5.65 | 1ku|
|Acl, min spec gain(V/V)||1|
|Vos (Offset Voltage @ 25C)(Max)(mV)||5|
|Vn at 1kHz(Typ)(nV/rtHz)||2.8|
|Number of Channels(#)||2|
|Operating Temperature Range(C)||-40 to 85,0 to 70|
|BW @ Acl(MHz)||100|
|Iq per channel(Typ)(mA)||8.3|
|Vn at Flatband(Typ)(nV/rtHz)||2.4|
|Package Group||SO PowerPAD|
|Pin nb||Package type||Ind std||JEDEC code||Package qty||Carrier||Device mark||Width (mm)||Length (mm)||Thick (mm)||Pitch (mm)|
|• Active Output Impedance for ADSL Line Drivers
Signal termination is very common in bidirectional communication systems. Termination allows for receiving signals while transmitting different signals at the same time. With the increasing popularity of asymmetrical digital subscriber lines (ADSL), the re | Doc
|• Noise Analysis for High Speed Op Amps (Rev. A)
As system bandwidths have increased, an accurate estimate of the noise contribution for each element in the signal channel has become increasingly important. Many designers are not, however, particularly comfortable with the calculations required to predic | Doc
|THS6032 PSpice Model (Rev. B) - ZIP (10/04/2011)|
|THS6032 TINA-TI Spice Model (Rev. A) - ZIP (10/04/2011)|
Central Office 1.35-W Total Power Dissipation for Full-Rate ADSL Into a 25- Load Low-Impedance Shutdown Mode Allows Reception of Incoming Signal During Standby Two Modes of Operation Class-G Mode: 4 Power Supplies, 1.35 W Power Dissipation Class-AB Mode: 2 Power Supplies, 2 W Power Dissipation Low Distortion THD = 62 dBc = 1 MHz, VO(PP) V, 25- Load THD = 69 dBc = 1 MHz, VO(PP) V, 25- Load 400-mA Minimum Output Current Into a 25- Load High Speed 65-MHz Bandwidth , 25- Load 100-MHz Bandwidth , 100- Load 1200 V/µs Slew Rate Thermal Shutdown and Short Circuit Protection Evaluation Module AvailableTHERMALLY ENHANCED SOIC (DWP) PowerPAD PACKAGE (TOP VIEW)
NC Not Connected This terminal is internally connected to the thermal pad. MicroStar Junior (GQE) PACKAGE (TOP VIEW)description
The is a low-power line driver ideal for asymmetrical digital subscriber line (ADSL) applications. This device contains two high-current, high-speed current-feedback drivers, which can be configured differentially for driving ADSL signals at the central office. The THS6032 features a unique class-G architecture to lower power consumption 1.35 W. The THS6032 can also be operated in a traditional class-AB mode to reduce the number of power supplies to two.
HIGH-SPEED xDSL LINE DRIVER/RECEIVER FAMILY DEVICE THS6072 THS7002 DRIVER RECEIVER ±15 V DESCRIPTION 500-mA differential line driver and receiver 500-mA differential line driver 250-mA differential line driver 500-mA low-power ADSL central-office line driver Low-noise ADSL receiver Low-power ADSL receiver Low-noise programmable-gain ADSL receiver
CAUTION: The THS6032 provides ESD protection circuitry. However, permanent damage can still occur if this device is subjected to high-energy electrostatic discharges. Proper ESD precautions are recommended to avoid any performance degradation or loss of functionality. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD and MicroStar Junior are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
The class-G architecture supplies current to the load from four supplies. For low output voltages (typically < +2.5), some of the output current is supplied from the +VCC(L) and VCC(L) supplies (typically ± 5 V). For large output voltages (typically 2.5 and + 2.5), the output current is supplied from +VCC(H) and VCC(H) (typically ± 15 V). This current sharing between VCC(L) and VCC(H) minimizes power dissipation within the THS6032 output stages for high crest factor ADSL signals. The THS6032 features a low-impedance shutdown mode, which allows the central office to receive incoming calls even after the device has been shut down. The THS6032 is available packaged in the patented PowerPAD package. This package provides outstanding thermal characteristics in a small-footprint surface-mount package, which is fully compatible with automated surface-mount assembly procedures. It is also available in the new MicroStar Junior BGA package. This package is only mm2 in area, allowing for high density PCB designs. Shutdown (SHDN1 and SHDN2) allows for powering down the internal circuitry for power conservation or for multiplexing. Separate shutdown controls are available for each channel on the THS6032. The control levels are TTL compatible. When turned off, each driver output is placed in a low impedance state which is determined by the voltage at DGND. This virtual ground at the outputs allows proper termination of a transmission line.
AVAILABLE OPTIONS PACKAGED DEVICES TA PowerPAD PLASTIC SMALL OUTLINE (DWP) THS6032CDWP MicroStar Junior BGA (GQE) THS6032CGQER PowerPAD TQFP (VFP) THS6032CVFP EVALUATION MODULES
to 85°C The DWP packages are available taped and reeled. Add an R suffix to the device type (i.e.,THS6032CDWPR) The GQE packages are only available taped and reeled.
TERMINAL NAME 2IN 2IN+ VCCH VCCH+ VCCL VCCL+ SHDN1 SHDN2 DGND PAD NC DWP PACKAGE TERMINAL NO. GQE PACKAGE TERMINAL NO. J4 J7 N/A VFP PACKAGE TERMINAL NO. N/AMicroStar Junior (GQE) PACKAGE (TOP VIEW)
NOTE: Shaded terminals are used for thermal connection to the ground plane. VFP PACKAGE (TOP VIEW)
|Related products with the same datasheet|
|Some Part number from the same manufacture Texas Instruments, Inc.|
|THS6032CDWP ti THS6032, Low-power Adsl Central Office Line Driver|
|THS6032CGQE Low-power Adsl Central-office Line Driver|
|THS6032CGQER ti THS6032, Low-power Adsl Central Office Line Driver|
|THS6032DWP Low-power Adsl Central-office Line Driver|
|THS6032IDWP ti THS6032, Low-power Adsl Central Office Line Driver|
|THS6032IGQE Low-power Adsl Central-office Line Driver|
|THS6032IGQER ti THS6032, Low-power Adsl Central Office Line Driver|
|THS6042CD ti THS6042, 350-mA, +/-12V Adsl Cpe Line Driver|
|THS6043CD ti THS6043, 350-mA, +/-12V Adsl Cpe Line Driver With Shutdown|
|THS6052CD ti THS6052, 175-mA, +/-12V Adsl Cpe Line Driver|
|THS6053CD ti THS6053, 175-mA, +/-12V Adsl Cpe Line Driver With Shutdown|
|THS6062 Low-noise Adsl Dual Differential Receiver|
|THS6062CD ti THS6062, Low-noise Adsl Dual Differential Receiver|
|THS6062D Low-noise Adsl Dual Differential Receiver|
CD74AC541M : Non-Inverting Buffers and Drivers ti CD74AC541, Non-inverting Octal Buffer/line Drivers With 3-State Outputs
TPS54972PWP : 9-A Active Bus Termination/ DDR Memory DC/DC Converter
BQ24081DRCR : The bq24080 and bq24081 are highly integrated and flexible Li-Ion linear charge devices targeted at space-limited charger applications. They offer an integrated power FET and current sensor, high-accuracy current and voltage regulation, charge status, and charge termination, in a single monolithic d
TACT83441 : AT CHIP SET
SN74HC132PWTE4 : 4-bit Synchronous Up/down Counters DUAL Clock WITH Clear
SN75LVDS9637DR : High-speed Differential LINE Receivers
CD40110 : CMOS Decade Up-down Counter/latch/display Driver
ADS7800KPG4 : Data Acquisition - Analog To Digital Converter (adc) Integrated Circuit (ics) 2 Single-Ended, Bipolar Tube Analog and Digital, Dual ±; IC 12BIT 333KHZ SMPL ADC 24-DIP Specifications: Number of Bits: 12 ; Package / Case: 24-DIP (0.300", 7.62mm) ; Data Interface: Parallel ; Packaging: Tube ; Sampling Rate (Per Second): 333k ; Operating Temperature: -40°C ~ 85°C ; Voltage Supply Source: Analog and Digital, Dual ± ; Number of Inputs and Type: 2 Single-Ended, Bipolar
TPS622313DRYR : Pmic - Voltage Regulator - Dc Dc Switching Regulator Integrated Circuit (ics) Step-Down (Buck) 500mA Yes; IC BUCK SYNC 1.3V 0.5A 6SON Specifications: Type: Step-Down (Buck) ; Output Type: Fixed ; PWM Type: Voltage Mode ; Synchronous Rectifier: Yes ; Number of Outputs: 1 ; Voltage - Output: 1.3V ; Current - Output: 500mA ; Frequency - Switching: 3MHz ; Voltage - Input: 2.05 V ~ 6 V ; Lead Free Status: Lead Free ; RoHS Status: RoHS
TMS320DM365ZCE30 : Embedded - Dsp (digital Signal Processors) Integrated Circuit (ics) Digital Media System-on-Chip (DMSoC) Tray 1.8V, 3.3V; IC DIGITAL MEDIA SOC 338NFBGA Specifications: Package / Case: 338-LFBGA ; Packaging: Tray ; Type: Digital Media System-on-Chip (DMSoC) ; Non-Volatile Memory: ROM (16 kB) ; On-Chip RAM: 56kB ; Interface: EBI/EMI, Ethernet, I²C, McBSP, SPI, UART, USB ; Voltage - I/O: 1.8V, 3.3V ; Voltage - Core: 1.35V ; Clock Rate: 300MHz
CD4082BPWE4 : Logic - Gate And Inverter Integrated Circuit (ics) AND Gate Tube 6.8mA, 6.8mA 3 V ~ 18 V; IC DUAL 4INPUT AND GATE 14TSSOP Specifications: Number of Circuits: 2 ; Package / Case: 14-TSSOP (0.173", 4.40mm Width) ; Logic Type: AND Gate ; Packaging: Tube ; Mounting Type: Surface Mount ; Number of Inputs: 4 ; Current - Output High, Low: 6.8mA, 6.8mA ; Operating Temperature: -55°C ~ 125°C ; Voltage - Supply: 3 V ~ 18 V ; Lea
2SK3320 : N-channel Junction Type ( For Low Noise Audio Amplifier Applications ).
BGB110 : BGB110; Bluetooth Radio Module. Plug-and-play Bluetooth class II radio module, needs only external antenna and reference clock Small dimensions x 1.9 mm) Fully compliant to Bluetooth radio v1.0 High sensitivity (typical -80 dBm) Advanced AFC for improved reception quality RSSI with high dynamic range BlueRF unidirectional JTAG RXMODE 2 compatible Simple interfacing to Philips VW2600X.
CVA2407T : Triple CRT Driver. The CVA2407T contains three high impedance, wideband amplifiers, designed specifically to drive a CRT. The device can drive monitors with resolutions x 1024 (non-interlaced) with pixel frequencies of 220MHz. The product is housed in the industry standard 11 lead TO-220 molded power package. ORDERING INFORMATION Part CVA2407T Package T11A Temperature.
EL5420C : Quad 12MHz Rail-to-Rail, I/o Op-amp. 12MHz -3dB bandwidth Supply voltage to 16.5V Low supply current (per amplifier) = 500µA High slew rate = 10V/µs Unity-gain stable Beyond the rails input capability Rail-to-rail output swing Ultra-small package The EL5420C and EL5220C are low power, high voltage, rail-to-rail input-output amplifiers. The EL5220C contains two amplifiers in one package,.
HTS-0010KD : Ultra High Speed Hybird Track-and Hold Amplifiers.
IH6116 : See DG506A.
L7372 : High Speed, High Output Current, Dual Operational Amplifier. LM7372 High Speed, High Output Current, Dual Operational Amplifier The is a high speed dual voltage feedback amplifier that has the slewing characteristic of current feedback amplifiers; yet it can be used in all traditional voltage feedback amplifier configurations. The LM7372 is stable for gains as low -1. It provides a very high slew rate at 3000V/µs.
LT6202 : LT6202, 100MHz, Ultralow 1.9nv/rtHz Noise, Low Power op Amp. LT6202/LT6203/LT6204 Single/Dual/Quad 100MHz, Rail-to-Rail Input and Output, Ultralow 1.9nV/Hz Noise, Low Power Op Amps Low Noise Voltage: 1.9nV/Hz (100kHz) Low Supply Current: 3mA/Amp Max Gain Bandwidth Product: 100MHz Dual LT6203 in Tiny DFN Package Low Distortion: at 1MHz Low Offset Voltage: 500µV Max Wide Supply Range: to 12.6V Input Common Mode.
M52755SP : Wide Band Analog Switch. The is a semiconductor integrated circuit for the RGBHV interface. The device switching signals input from two types of image sources and outputting the signals to the CRT display, etc. Synchronous signals, meeting a frequency band to 200kHz, are output at TTL. The frequency band of video signals is 250MHz, acquiring high-resolution images, and are optimum.
M65657FP : Scan Converter. The is an integrated circuit that converts digital VGA inputs directly into NTSC/PAL TV format outputs. This circuit integrates a digital NTSC/PAL encoder with 10bit DAC's. VGA picture signal to NTSC / PAL signal conversion Input Format, 60Hz, 640×480 (Standard VGA format) High performance Non-Flicker Filter Built-in Line Memories Fully integrated with.
MAX270CPP : Digitally-programmed, Dual 2nd-order Continuous Lowpass Filters.
MRFIC1805 : 1.9 GHZ Power Amplifier GAAS Monolithic Integrated Circuit. This twostage class AB monolithic GaAs amplifier in a lowcost 16 lead plastic package is designed for output or driver applications in 1.9 GHz PCS handsets and basestations. The design is optimized for 3.0 Volt operation in systems such as Japan's PHS, Europe's DECT and the emerging North American PCS services. With modifications to the simple offchip.
OP249ARC/883 : Dual, Precision JFET High Speed Operational Amplifier. Dual, Precision JFET High Speed Operational Amplifier OP249 PIN CONNECTIONS 8-Lead Cerdip (Z Suffix), 8-Lead Plastic Mini-DIP (P Suffix) Fast Slew Rate: V/ s typ Settling Time 1.2 s max Offset Voltage: 300 V max High Open-Loop Gain: 1000 V/mV min Low Total Harmonic Distortion: 0.002% typ Improved Replacement for OP215, TL072 and MC34082 Available in Die Form.
PF0414A : MOSFET Power Amplifier Module For DCS 1800 Handy Phone. 3stage amplifier Small package: 0.2cc High efficiency: 45% Typ High speed switching: 0.9 µsec Item Supply voltage Supply current VAPC voltage Input power Operating case temperature Storage temperature Output power Symbol VDD I DD VAPC Pin Tc (op) Tstg Pout Rating +100 3 Unit °C W Item Frequency range Control voltage range Drain cutoff current Total.
SL311 : High Performance Voltage Comparators. Input polarity is reversed when GND pin is used as an output. Symbol VCC + VEE VO - VEE VID VIN 1/ JA TJ(max) Tstg Parameter Total Supply Voltage Output to Negative Supply Voltage Ground to Negative Supply Voltage Input Differential Voltage Input Voltage (Note) Voltage at Strobe Pin Power Dissipation and Thermal Characteristics Plastic Dual In-Line.
STK4221V : 2-channel 80W af Power Amplifier. The inclusion of a muting circuit on-chip allows all types of impulse noise to be excluded. Current mirror circuit application reduces distortion to 0.008%. Pin compatible with the STK4201II Series (THD = 0.4%) and the STK4141X Series (THD = 0.02%) s Parameter Maximum supply voltage Thermal resistance Junction temperature Operating case temperature.
TL3X071 : Single. High-slew-rate, Single-supply op Amp. Wide Gain-Bandwidth Product. 4.5 MHz High Slew Rate. 13 V/µs Fast Settling Time. to 0.1% Wide-Range Single-Supply Operation 44 V Wide Input Common-Mode Range Includes Ground (VCC Low Total Harmonic Distortion. 0.02% Low Input Offset Voltage. 3 mV Max (A Suffix) Large Output Voltage Swing 14 V (With ± 15-V Supplies) Large Capacitance Drive Capability.
TLV2773AID : ti TLV2773A, Dual 2.7-V High-slew-rate Rail-to-rail Output Operational Amplifier W/shutdown.