Details, datasheet, quote on part number: THS6007CPWPR
PartTHS6007CPWPR
CategoryCommunication => DSL (Digital Subscriber Line) => DSL Analog Front Ends => DSL Line Drivers and Receivers
TitleDSL Line Drivers and Receivers
Descriptionti THS6007, Dual Differential Line Drivers And Low-power Receivers
CompanyTexas Instruments, Inc.
DatasheetDownload THS6007CPWPR datasheet
Quote
Find where to buy
 
  

 

Features, Applications
THS6007 DUAL DIFFERENTIAL LINE DRIVERS AND LOW-POWER RECEIVERS

ADSL Differential Line Driver and Receiver Driver Features 140 MHz Bandwidth (3dB) With 25- Load 1300 V/s Slew Rate, G mA Output Current Minimum Into 25- Load 72 dBc 3rd Order Harmonic Distortion = 1 MHz, 25- Load, and 20 VO(PP) Receiver Features 175 MHz Bandwidth 230 V/s Slew Rate 79 dBc Total Harmonic Distortion = 1 MHz, k Quiescent Current 3.4 mA Per Channel Wide Supply Range 16 V Available in the PowerPADTM Package

description

The THS6007 contains two high-current, high-speed drivers and two low-power, high-speed receivers. These drivers and receivers can be configured differentially for driving and receiving signals over low-impedance lines. The THS6007 is ideally suited for asymmetrical digital subscriber line (ADSL) applications where it supports the high-peak voltage and current requirements of that application. The drivers are current feedback amplifiers designed for the high slew rates necessary to support low total harmonic distortion (THD) in ADSL applications. The receivers are traditional voltage feedback amplifiers designed for maximum flexibility while consuming only 3.4 mA per channel quiescent current. Separate power supply connections for each driver and both receivers are provided to minimize crosstalk. The THS6007 is packaged in the patented PowerPADTM package. This package provides outstanding thermal characteristics in a small footprint package, which is fully compatible with automated surface-mount assembly procedures. The exposed thermal pad on the underside of the package is in direct contact with the die. By simply soldering the pad to the PWB copper and using other thermal outlets, the heat is conducted away from the junction.

AVAILABLE OPTIONS to 85C PACKAGED DEVICE PowerPADTM TSSOP (PWP) THS6007CPWP THS6007IPWP EVALUATION MODULE THS6007EVM

The PWP packages are available taped and reeled. Add an R suffix to the device type (i.e., THS6007PWPR)

CAUTION: The THS6007 provides ESD protection circuitry. However, permanent damage can still occur if this device is subjected to high-energy electrostatic discharges. Proper ESD precautions are recommended to avoid any performance degradation or loss of functionality.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

absolute maximum ratings over operating free-air temperature (unless otherwise noted)

Supply voltage, VCC+ to VCC. 33 V Input voltage, VI (driver and receiver). VCC Output current, IO (driver) (see Note 800 mA Output current, IO (receiver) (see Note 150 mA Differential input voltage, VID (driver and receiver). 4 V Maximum junction temperature, TJ. 150C Continuous total power dissipation at (or below) = 25C (see Note 4.48 W Operating free air temperature, TA. to 85C Storage temperature, Tstg. to 125C Lead temperature, mm (1/16 inch) from case for 10 seconds. 300C

Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: The THS6007 incorporates a PowerPadTM on the underside of the chip. This acts as a heatsink and must be connected to a thermal dissipation plane for proper power dissipation. Failure do so can result in exceeding the maximum junction temperature, which could permanently damage the device. See the Thermal Information section of this document for more information about PowerPadTM technology.

MIN Supply voltage voltage, VCC+ CC and VCC Operating free-air temperature, TA Split supply Single supply TYP MAX UNIT V C

Driver CC D1 IN+ 8 D1 IN _ 7 Driver 2 D2 IN+ D2 IN 22 R VCC+ 28 Receiver VCC D2 OUT 19 D VCC D VCC+ D1 OUT


 

Related products with the same datasheet
THS6007IPWP
THS6007IPWPR
Some Part number from the same manufacture Texas Instruments, Inc.
THS6007IPWP ti THS6007, Dual Differential Line Drivers And Low-power Receivers
THS6012 500-ma Dual Differential Line Driver
THS6012CDWP ti THS6012, 500-mA Dual Differential Line Driver
THS6012CGQE 500-ma Dual Differential Line Driver
THS6012EVM
THS6012GQE
THS6012IDWP ti THS6012, 500-mA Dual Differential Line Driver
THS6012IGQE 500-ma Dual Differential Line Driver
THS6012IGQER ti THS6012, 500-mA Dual Differential Line Driver
THS6022 250-ma Dual Differential Line Driver
THS6022CGQE
THS6022CGQER ti THS6022, 250-mA Dual Differential Line Driver
THS6022EVM 250-ma Dual Differential Line Driver
THS6022GQE
THS6022IGQER ti THS6022, 250-mA Dual Differential Line Driver
THS6022PWP 250-ma Dual Differential Line Driver
THS6032 Low-power Adsl Central-office Line Driver
THS6032CDWP ti THS6032, Low-power Adsl Central Office Line Driver
THS6032CGQE Low-power Adsl Central-office Line Driver
THS6032CGQER ti THS6032, Low-power Adsl Central Office Line Driver
THS6032DWP Low-power Adsl Central-office Line Driver

78HT200 : 2 Amp Positive Step-down Integrated Switching Regulator

BQ2011SN-D118 : Gas Gauges ti BQ2011, Nicd Gas Gauge For High Discharge Rates (>5A), Small Pack Capacities (<2Ah)

SN55188J : ti SN55188, Quadruple Line Driver

SN74ALVCH16271DGGR : Universal Bus Exchangers (UBEs) ti SN74ALVCH16271, 12-Bit to 24-Bit Multiplexed Bus Exchanger With 3-State Outputs

TPS3123G15DBVT : ti TPS3123G15, Ultra-low Voltage Processor Supervisory Circuit

SN74BCT8240ANTE4 : SCAN TEST Devices WITH Octal D-type Edge-triggered Flip-flops

CD54HC4024_07 : High-speed CMOS Logic Dual Retriggerable Precision Monostable Multivibrator

UCC3957M-1G4 : IC, BATTERY PROTEC, LI-ION 4CELL SSOP-16 Specifications: Battery Type: Li-Ion ; IC Interface Type: - ; Battery Protection: Over Current ; No. of Batteries: 4 ; Shutdown Current: 3.5A ; Supply Voltage Range: 6.5V to 20V ; Battery IC Case Style: SSOP ; No. of Pins: 16 ; Operating Temperature Range: -20C to +70C ; MSL: -

LM3S800-EGZ50-C2 : Embedded - Microcontroller Integrated Circuit (ics) Internal Tray 3 V ~ 3.6 V; IC ARM CORTEX MCU 64KB 48VQFN Specifications: Program Memory Size: 64KB (64K x 8) ; RAM Size: 8K x 8 ; Number of I /O: 36 ; Package / Case: 48-VFQFN Exposed Pad ; Speed: 50MHz ; Oscillator Type: Internal ; Packaging: Tray ; Program Memory Type: FLASH ; EEPROM Size: - ; Core Processor: ARM Cortex-M3 ; Data Converters: - ; Core

TPS3618-50DGKRG4 : Pmic - Supervisor Integrated Circuit (ics) Battery Backup Circuit Tape & Reel (TR) 1; IC BATTERY BACKUP SVS 5V 8-MSOP Specifications: Output: Push-Pull, Totem Pole ; Reset: Active Low ; Package / Case: 8-TSSOP, 8-MSOP (0.118", 3.00mm Width) ; Packaging: Tape & Reel (TR) ; Number of Voltages Monitored: 1 ; Reset Timeout: 60 ms Minimum ; Type: Battery Backup Circuit ; Voltage - Threshold: 4.55V ; Operating Temper

TPS22953DQCR : Power Switch ICs - Power Distribution 5A Load SW w/ Voltage Monitoring & PG

 
0-C     D-L     M-R     S-Z