Details, datasheet, quote on part number: BQ2083DBTR
PartBQ2083DBTR
CategoryPower Management => Battery Management => Gas Gauges
TitleGas Gauges
Descriptionti BQ2083, SBS Compliant Gas Gauge ic For Use With BQ29311
CompanyTexas Instruments, Inc.
DatasheetDownload BQ2083DBTR datasheet
Quote
Find where to buy
 
  

 

Features, Applications

FEATURES D Provides Accurate Measurement of Available D Drives or 5-Segment LED Display for D

Charge in Li-Ion and Li-Polymer Batteries Supports the Smart Battery Specification (SBS) V1.1 Works With the TI bq29311 Analog Front End (AFE) Protection IC to Provide Complete Pack Electronics for or 14.4-V Battery Packs With Few External Components Based on a Powerful Low-Power RISC CPU Core With High-Performance Peripherals Integrated Flash Memory Eliminates the Need for External Configuration EEPROM Measures Charge Flow Using a High Resolution 16-Bit Integrating Converter - Better Than 3-nVh of Resolution - Self-Calibrating - Offset Error Less Than 1-V Uses 16-Bit Delta Sigma Converter for Accurate Voltage and Temperature Measurements Programmable Cell Modeling for Maximum Battery Fuel Gauge Accuracy

APPLICATIONS D Notebook PCs D Medical and Test Equipment D Portable Instrumentation DESCRIPTION

The bq2083-V1P2 SBS-compliant gas gauge IC for battery pack or in-system installation maintains an accurate record of available charge in Li-ion or Li-polymer batteries. The bq2083-V1P2 monitors capacity and other critical parameters of the battery pack and reports the information to the system host controller over a serial communication bus. It is designed to work with the bq29311 analog front-end (AFE) protection IC to maximize functionality and safety and minimize component count and cost in smart battery circuits. Using information from the bq2083-V1P2, the host controller can manage remaining battery power to extend the system run time as much as possible.

Pack+ Charge/Discharge Power FETs Supply Voltage SMBus LDO bq29311 bq2083-V1P2 Glueless Interface Cell Inputs Safety Control Level Translator - + Li-Ion - Cells + -

Temp Sensor 512 Bytes Config. Flash EPROM

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

The bq2083-V1P2 uses an integrating converter with continuous sampling for the measurement of battery charge and discharge currents. Optimized for coulomb counting in portable applications, the self-calibrating integrating converter has a resolution better than 3-nVh and an offset measurement error of less than 1-V (typical). For voltage and temperature reporting, the bq2083-V1P2 uses a 16-bit A-to-D converter. In conjunction with the bq29311, the onboard ADC also monitors individual cell voltages in a battery pack and allows the bq2083-V1P2 to generate the control signals necessary to implement the cell balancing and the required safety protection for Li-ion and Li-polymer battery chemistries. The bq2083-V1P2 supports the Smart Battery Data (SBData) commands and charge-control functions. It communicates data using the System Management Bus (SMBus) 2-wire protocol. The data available include the battery's remaining capacity, temperature, voltage, current, and remaining run-time predictions. The bq2083-V1P2 provides LED drivers and a push-button input to depict remaining battery capacity from full to empty or 33% increments with or 5-segment display. The bq2083-V1P2 contains 512 bytes of internal data flash memory, which store configuration information. The information includes nominal capacity and voltage, self-discharge rate, rate compensation factors, and other programmable cell-modeling factors used to accurately adjust remaining capacity for use-conditions based on time, rate, and temperature. The bq2083-V1P2 also automatically calibrates or learns the true battery capacity in the course of a discharge cycle from programmable near full to near empty levels. The bq29311 AFE protection IC provides power to the bq2083-V1P2 from or 4 series Li-ion cell stack, eliminating the need for an external regulator circuit.

VIN TS OC N/C SCLK N/C VDDD RBI SDATA VSSD SAFE N/C SMBC SMBD DISP EVENT VSSD
VSSD N/C CLKOUT XCK1 XCK2 FILT VDDA VSSA SR1 SR2 MRST N/C LED4 LED5
- No internal connection AVAILABLE OPTIONS TA PACKAGE 38-PIN TSSOP (DBT)

bq2083DBT-V1P2 (1) The bq2083-V1P2 is available taped and reeled. Insert an R suffix to the device type (e.g., bq2083DBTR-V1P2) to order tape and reel version.

TERMINAL NAME CLKOUT DISP FILT EVENT LED4 LED5 MRST N/C OC RBI SAFE SCLK SDATA SMBC SMBD SR2 TS VDDA VDDD VIN VSSA VSSD XCK1 XCK2 No. I/O Connections for a small-value sense resistor to monitor the battery charge- and discharge-current flow Thermistor voltage input connection to monitor temperature Positive supply for analog circuitry Positive supply for digital circuitry and I/O pins Single cell voltage input from the bq29311 Negative supply for analog circuitry Negative supply for digital circuitry 32.768 kHz crystal oscillator input pin 32.768 kHz crystal oscillator output pin Master reset input that forces the device into reset when held high No connection Analog input for auto ADC offset compensation; should be connected to VSSA Register backup that provides backup potential to the bq2083-V1P2 data registers during periods of low operating voltage. RBI accepts a storage capacitor or a battery input. Output for additional level of safety protection; e.g., fuse blow. Communication clock to the bq29311 Data transfer to and from bq29311 SMBus clock open-drain bidirectional pin used to clock the data transfer to and from the bq2083-V1P2 SMBus data open-drain bidirectional pin used to transfer address and data to and from the bq2083-V1P2 LED display segments that each may drive an external LED 32.768-kHz output to the bq29311 Display control for the LED drivers LED1 through LED5 Analog input connected to the external PLL filter Input from bq29311 XALERT output DESCRIPTION


 

Related products with the same datasheet
BQ2083DBT-V1P2
BQ2083DBT-V1P3
BQ2083DBTR-V1P2
BQ2083DBTR-V1P3
Some Part number from the same manufacture Texas Instruments, Inc.
BQ2083DBTR-V1P2 SBS Compliant Gas Gauge ic For Use With BQ29311
BQ2083DBTR-V1P2 ti BQ2083, SBS Compliant Gas Gauge ic For Use With BQ29311
BQ2083DBTR-V1P3 SBS Compliant Gas Gauge ic For Use With BQ29311
BQ2083DBTR-V1P3 ti BQ2083, SBS Compliant Gas Gauge ic For Use With BQ29311
BQ2084 SBS Compliant Gas Gauge For Use With The Bq29312
BQ2084DBT ti BQ2084, SBS Compliant Gas Gauge For Use With The Bq29312
BQ2084DBTR SBS Compliant Gas Gauge For Use With The Bq29312
BQ2084DBTR ti BQ2084, SBS Compliant Gas Gauge For Use With The Bq29312
BQ2085 SBS 1.1 Compliant Gas Gauge With Integrated Oscillator For Use With The Bq29311
BQ20851 V1P2 Sbs-compliant Gas Gauge ic For Use With The Bq29311
BQ20851DBT-V1P2 ti BQ20851, V1P2 Sbs-compliant Gas Gauge ic For Use With The Bq29311
BQ20851DBTR-V1P2 V1P2 Sbs-compliant Gas Gauge ic For Use With The Bq29311
BQ20851DBTR-V1P2 ti BQ20851, V1P2 Sbs-compliant Gas Gauge ic For Use With The Bq29311
BQ2085DBT SBS 1.1 Compliant Gas Gauge With Integrated Oscillator For Use With The Bq29311
BQ2085DBT ti BQ2085, SBS 1.1 Compliant Gas Gauge With Integrated Oscillator For Use With The Bq29311
BQ2085DBT-V1P2 SBS 1.1 Compliant Gas Gauge With Integrated Oscillator For Use With The Bq29311
BQ2085DBT-V1P2 ti BQ2085, SBS 1.1 Compliant Gas Gauge With Integrated Oscillator For Use With The Bq29311
BQ2085DBT-V1P3 SBS 1.1 Compliant Gas Gauge With Integrated Oscillator For Use With The Bq29311
BQ2085DBT-V1P3 ti BQ2085, SBS 1.1 Compliant Gas Gauge With Integrated Oscillator For Use With The Bq29311
BQ2085DBTR SBS 1.1 Compliant Gas Gauge With Integrated Oscillator For Use With The Bq29311
BQ2085DBTR ti BQ2085, SBS 1.1 Compliant Gas Gauge With Integrated Oscillator For Use With The Bq29311

CY74FCT162841CTPVC : D-Type (3-State) Latches ti CY74FCT162841T, 20-Bit Bus Interface D-type Latches With 3-State Outputs

CY74FCT163500CPACT : Universal Bus Transceivers (UBTs) ti CY74FCT163500, 18-Bit Universal Bus Transceivers With 3-State Outputs

PT5406N : Plug-in Power Solutions->Non-Isolated->Single Posi ti PT5406, 1.2V 6A, 3.3/5-V Input, Adjustable Swift Module

SN54ALS374AJ : D-Type (3-State) Flip-Flops ti SN54ALS374A, Octal D-type Edge Triggered Flip-flops With 3-State Outputs

SN74AS10DR : ti SN74AS10, Triple 3-Input Positive-nand Gates

TMS370C010C : CISC 8-bit Microcontroller

UCC383TD-5 : Adj - Low Power 3 Ampere Low Dropout (LDO) Regulator

TLC0834IDRG4 : Data Acquisition - Analog To Digital Converter (adc) Integrated Circuit (ics) 8 Single-Ended, Unipolar; 4 Differential, Unipolar Tape & Reel (TR) Single Supply; IC ADC 8BIT 4CH SRL I/O 14-SOIC Specifications: Number of Bits: 8 ; Package / Case: 14-SOIC (0.154", 3.90mm Width) ; Data Interface: Serial ; Packaging: Tape & Reel (TR) ; Sampling Rate (Per Second): 20k ; Operating Temperature: -40C ~ 85C ; Voltage Supply Source: Single Supply ; Number of Inputs and Type: 8 Single-Ended, Un

DAC8581IPWG4 : Data Acquisition - Digital To Analog Converter (dac) Integrated Circuit (ics) Tube Analog and Digital, Dual ; IC DAC 16BIT HI-SPD LN 16-TSSOP Specifications: Data Interface: Serial ; Number of Bits: 16 ; Operating Temperature: -40C ~ 85C ; Package / Case: 16-TSSOP (0.173", 4.40mm Width) ; Packaging: Tube ; Voltage Supply Source: Analog and Digital, Dual ; Settling Time: 650ns ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

74AHCT1G04DBVTG4 : Logic - Gate And Inverter Integrated Circuit (ics) Inverter Tape & Reel (TR) 8mA, 8mA 4.5 V ~ 5.5 V; IC SNGL INVERTER GATE SOT23-5 Specifications: Number of Circuits: 1 ; Package / Case: SC-74A, SOT-753 ; Logic Type: Inverter ; Packaging: Tape & Reel (TR) ; Mounting Type: Surface Mount ; Number of Inputs: 1 ; Current - Output High, Low: 8mA, 8mA ; Operating Temperature: -40C ~ 85C ; Voltage - Supply: 4.5 V ~ 5.5 V ; Lead

BQ24151AEVM : Eval And Demo Board And Kit Programmers, Development System; EVAL MODULE FOR BQ24151A Specifications: Main Purpose: Power Management, Battery Charger ; Primary Attributes: 1 Cell- Li-Ion/ Li-Pol, 1.25A, 4 ~ 6 V Input ; Secondary Attributes: I²C Interface ; Supplied Contents: Board ; Utilized IC / Part: BQ24151A ; Embedded: No ; Lead Free Status: Lead Free ; RoHS Status: RoHS

PGA2505EVM : Eval And Demo Board And Kit Programmers, Development System; EVAL MODULE FOR PGA2505 Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

 
0-C     D-L     M-R     S-Z