|Category||Interface and Interconnect|
|Description||High Speed Differential Line Receivers|
|Company||ST Microelectronics, Inc.|
|Datasheet||Download STLVDS9637B datasheet
MEETS OR EXCEEDS THE REQUIREMENTS OF ANSI TIA/EIA-644 STANDARD OPERATES WITH A SINGLE 3.3V SUPPLY DESIGNED FOR SIGNALING RATE TO 400Mbps DIFFERENTIAL INPUT THRESHOLDS ±100mV MAX TYPICAL PROPAGATION DELAY TIME OF 2.5ns POWER DISSIPATION 60mW TYPICAL PER RECEIVER AT 200MHz LOW VOLATGE TTL (LVTTL) LOGIC OUTPUT LEVELS OPEN CIRCUIT FAIL SAFE ESD PROTECTION: 7KV RECEIVER PINS 3KV ALL PINS VS GND
DESCRIPTION The is a differential line receiver that implements the electrical characteristics of low voltage differential signaling (LVDS). This signaling technique lowers the output voltage levels of 5V differential standard levels (such TIA/EIA-422B) to reduce the power, increase the switching speeds and allow operations with a 3.3V supply rail. This differential receiver provides a ORDERING CODES
valid logical output state with a 3.3V supply rail. It also provides a valid logical output state with a ±100mV differential input voltage within the input common mode voltage range. The input common mode voltage allows 1V of ground potential difference between two LVDS nodes. The intended application of this device and signalling technique is both point-to-point and multidrop data transmission over controlled impedance media approximately 100. The transmission media may be printed circuit board traces, backplanes or cables. The ultimate rate and distance of data transfer depend upon the attenuation characteristics of the media and noise coupling to the environment. The STLVDS9637 version is characterized for operation from to 85°C.
PlN N° SYMBOL to 2A GND VCC NAME AND FUNCTION Receiver Outputs Negated Receiver Inputs Receiver Inputs Ground Supply VoltageL = Low level, H = High Level, X = Don't care, Z = High Impedance, ? = Indeterminate
Symbol VCC VI ESD Tstg Supply Voltage (Note 1) Input Voltage Input Voltage or B inputs) Human Body Model Storage Temperature Range Pins Receivers All Pins vs GND Parameter Value -0.5 to (VCC to +150 Unit KV °C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. Note 1: All voltages except differential I/O bus voltage, are with respect to the network ground terminal.
Symbol VCC VIH VIL |VID| VIC TA Supply Voltage HIGH Level Input Voltage (ENABLE) LOW Level Input Voltage (ENABLE) Magnitude of Differential Input Voltage Common Mode Input Voltage Operating Temperature Range 0.5|VID| -40 Parameter Min. 2.4-0.5|VID| VCC 85 °C Typ. 3.3 Max. 3.6 Unit
ELECTRICAL CHARACTERISTICS (Over recommended operating conditions unless otherwise noted. All typical values are = 25°C, and VCC = 3.3V)
Symbol VITH+ VITHVOH VOL ICC II II(OFF) IIH IIL IOZ Parameter Positive Going Differential Input Voltage Threshold Negative Going Differential Input Voltage Threshold High Level Output Voltage Low Level Output Voltage Supply Current Test Conditions Min. Typ. Max. 100 -100 IOH = -8mA IOH = -4mA IOH 8mA No Load = 2.4V Power off Input Current or B inputs) High Level Input Current (EN, G or Inputs) Low Level Input Current (EN, G or Inputs) High Impedance Output Current VCC = 0 VIH = 2V VIL 0 or VCC mA µA Unit mV V
|Related products with the same datasheet|
|Some Part number from the same manufacture ST Microelectronics, Inc.|
|STLVDS9637BD High Speed Differential Line Receivers|
|STM1001 Reset Circuit|
|STM1645-10 RF Power Module Satellite Communications Applications|
|STM2DPFS30L P - Channel 30v - 0.145ohm - 2a Minis0-8 StripFET MOSFET Plus Schottky Rectifier|
|STM351-2 RF Power Module Wireless Local Loop Applications|
|STM6316 DVD Optical Disc - Integrated Solution For DVD Players|
|STM690 3V Supervisor With Battery Switchover|
|STM690A 5V Supervisor With Battery Switchover|
|STM690RM6E 3V Supervisor With Battery Switchover|
|STM705 5V Supervisor|
|STM706 3V Supervisor|
|STM707 5V Supervisor|
|STM708 3V Supervisor|
|STM795 3V Supervisor With Battery Switchover|
|STM7E1 7 e 1 Channels Switch Array|
|STm8000 Dvd-recorder Market With System-on-chip Solution|
|STM802 Solenoid Controller ic|
|STM804 3V Supervisor With Battery Switchover|
ST72T311N4T6S : ST7 Family 8-BIT Microcontroller (MCU) With 8 to 16K ROM/OTP/EPROM,384 to 512 Bytes RAM,adc,wdg,sci,spi And 2 Timers - SDIP42/56, QFP44/64
M58WR064KL : 64 Mbit (4Mb x 16, Multiple Bank, Burst ) 1.8V Supply Flash Memory
NAND512W4M5BZB5E : 256/512mb/1gb (x8/x16, 1.8/3v, 528 Byte Page) NAND Flash Memories + 256/512mb (x16/x32, 1.8v) Lpsdram, MCP
PSD854F5-70UT : Flash In-system Programmable ISP Peripherals For 8-bit MCUs
M45PE80-VMN6G : 8 Mbit, low Voltage, Page-erasable Serial Flash Memory with byte Alterability and a 50 MHz SPI bus Interface
M95080-WDW6TP : 16kbit and 8kbit Serial SPI Bus Eeprom With High Speed Clock
TDA7706 : Rf Receiver Rf/if And Rfid; IC TUNER AM/FM CAR RADIO 64LQFP Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant
M69KB048BD70W8T : 2M X 16 PSEUDO STATIC RAM, 70 ns, UUC Specifications: Memory Category: SRAM Chip ; Density: 33554 kbits ; Number of Words: 2000 k ; Bits per Word: 16 bits ; Package Type: ROHS COMPLIANT, WAFER ; Logic Family: CMOS ; Supply Voltage: 1.8V ; Access Time: 70 ns ; Operating Temperature: -30 to 85 C (-22 to 185 F)
5962-8515507SX : HC/UH SERIES, ASYN NEGATIVE EDGE TRIGGERED 12-BIT UP BINARY COUNTER, CDFP16 Specifications: Counter Type: BINARY COUNTER ; Counter Category: Asynchronous ; Counter Direction: UP ; Supply Voltage: 4.5 ; Package Type: CERAMIC, FP-16 ; Logic Family: CMOS, HC/UH ; Number of Pins: 16 ; Number of Stages (Bits): 12 bits ; Clock Frequency: 22 MHz ; Operating Temperature: -55 to 125
FIN1019 : 3.3V LVDS High Speed Differential Driver/receiver. This driver and receiver pair are designed for high speed interconnects utilizing Low Voltage Differential Signaling (LVDS) technology. The driver translates LVTTL signals to LVDS levels with a typical differential output swing of 350mV and the receiver translates LVDS signals, with a typical differential input threshold of 100mV, into LVTTL levels.
IMP2119 : SCSI Terminator. 28 Tssop 9-Line ULTRA3 Lvd/se Scsi Terminator. The is a multimode SCSI terminator that conforms to the SCSI Parallel Interconnect-2 (SPI-2) developed by the T10 standards committee for low voltage differential (LVD) termination. Multimode compatibility permits the use of legacy devices on the bus without hardware alterations. Automatic mode selection is achieved through voltage detection on the diffsense.
IT8673F : Advanced Isa I/o. If you have any marketing or sales questions, please contact: Lawrence Liu, at ITE Taiwan: E-mail: firstname.lastname@example.org, Tel: 886-2-29126889 X6071, Fax: 886-2-29102551 David Lin, at ITE U.S.A: E-mail: email@example.com, Tel: 980-8168 X238, Fax: (408) 980-9232 Don Gardenhire, at ITE Eastern USA Office: E-mail: firstname.lastname@example.org, Tel: (512).
JM38510/12905BPA : ti SN55454B, Dual Very-high Speed, High-current Peripheral Drivers. PERIPHERAL DRIVERS FOR HIGH-CURRENT SWITCHING AT VERY HIGH SPEEDS Characterized for Use 300 mA High-Voltage Outputs No Output Latch-Up 20 V (After Conducting 300 mA) High-Speed Switching Circuit Flexibility for Varied Applications TTL-Compatible Diode-Clamped Inputs Standard Supply Voltages Plastic DIP (P) With Copper Lead Frame Provides Cooler Operation.
LC75750W : . The LC75750E and LC75750W are 1/3 duty VFD drivers that can be used for electronic tuning frequency display and other applications under the control of a microcontroller. These products can directly drive VFDs with to 264 segments. 264 segment outputs. Noise reduction circuits are built into the output drivers. Serial data input supports CCB format.
LSI53C895 : SCSI integrated circuits. Pci to Ultra2 Scsi I/o Processor With LVD Link Universal Transceivers Technical Manual V3.2 12/00.
MC74F3893AFN : Quad Futurebus Backplane Transceiver ( 3 State + Open Collector ). MC74F3893A QUAD FUTUREBUS BACKPLANE TRANSCEIVER (3 STATE + OPEN COLLECTOR) The is a quad backplane transceiver and is intended to be used in very high speed bus systems. The MC74F3893A interfaces to "Backplane Transceiver Logic" (BTL). BTL a reduced (1 V) voltage swing for lower power consumption and a series diode on the drivers to reduce capacitive.
RTI-1260 : Time Interface Cards. High Performance STD Bus Compatible Analog I/o Subsystem.
SN65ALS1176 : Differential Bus Transceiver. Meets or Exceeds the Requirements TIA/EIA-422-B, TIA/EIA-485-A, and ITU Recommendations V.11 and X.27 Recommended for PROFIBUS Applications Operates at Data Rates to 35 MBaud Operating Temperature Range. to 85°C Designed for Multipoint Transmission on Long Bus Lines in Noisy Environments Low Supply-Current Requirement. 30 mA Max Wide Positive and Negative.
SN65LVDS051 : High-speed Differential Line Receiver. Meets or Exceeds the Requirements of ANSI TIA/EIA-644-1995 Standard Signaling Rates to 400 Mbps Bus-Terminal ESD Exceeds 12 kV Operates From a Single 3.3-V Supply Low-Voltage Differential Signaling With Typical Output Voltages 350 mV and a 100- Load Propagation Delay Times Driver: 1.7 ns Typ Receiver: 3.7 ns Typ Power Dissipation at 200 MHz Driver:.
ST72E631K1B0 : Low Speed Usb 8-bit MCU Family With up to 16k Memory, up to 512 Bytes RAM, 8-bit ADC, Wdg, Timer, Sci & I2c.
ST75C176B : Low Power RS784/RS422 Transceiver. LOW QUIESCENT CURRENT: 300µA DESIGNED FOR RS-485 INTERFACE APPLICATIONS TO 12V COMMON MODE INPUT VOLTAGE RANGE DRIVER MAINTAINS HIGH IMPEDANCE 3-STATE OR WITH THE POWER OFF 70mV TYPICAL INPUT HYSTERESIS 30ns PROPAGATION DELAYS, 5ns SKEW OPERATE FROM A SINGLE 5V SUPPLY CURRENT LIMITING AND THERMAL SHUTDOWN FOR DRIVER OVERLOAD PROTECTION ALLOWS TO 32 TRANSCEIVERS.
WLP200 : Evaluation RC Filter Network - Not Recommended For New Designs..
NCV7356 : Single Wire CAN The NCV7356 is a physical layer device for a single wire data link capable of operating with various Carrier Sense Multiple Access with Collision Resolution (CSMA/CR) protocols such as the Bosch Controller Area Network (CAN) version 2.0. This serial data link network is intended for use in applications where high data rate is not required.
SLK2511B : The SLK2511B is a single chip multirate transceiver IC used to derive high-speed timing signals for SONET/SDH based equipment. The chip performs clock and data recovery, serial-to-parallel/parallel-to-serial conversion and frame detection function conforming to the SONET/SDH standards. The device can be configured to operate under OC-48, OC-24, OC-12,.
DS15EA101 : The DS15EA101 is an adaptive equalizer optimized for equalizing data transmitted over copper cables. The DS15EA101 operates over a wide range of data rates from 150 Mbps to 1.5+ Gbps and automatically adapts to equalize any cable length from zero meters to lengths that attenuate the signal by 35 dB at 750 MHz. The DS15EA101 allows either single-ended.
SN65HVD1040 : Industrial CAN Transceiver with Ultra Low Power Sleep mode and Remote Bus Wake-up The SN65HVD1040 meets or exceeds the s of the ISO 11898 standard for use in applications employing a Controller Area Network (CAN). As CAN transceivers, these devices provide differential transmit and receive capability for a CAN controller at signaling rates of up to 1 megabit.
AD8197A : 4:1 HDMI/DVI Switch With Equalization The AD8197A is an HDMI??/DVI switch featuring equalized TMDS?? inputs and pre-emphasized TMDS outputs, ideal for systems with long cable runs. Outputs can be set to a high impedance state to reduce the power dissipation and/or to allow the construction of larger arrays using the wire-OR technique. The AD8197A is provided.