Details, datasheet, quote on part number: SP6201EM5-3.3/TR
PartSP6201EM5-3.3/TR
CategoryPower Management => Regulators => Linear Regulators => LDO (Low Drop Out)
DescriptionIout = 100mA ;; Vin Min. = 2.5V ;; Vin Max. = 7V ;; Iq = 28µA ;; Acc = 2% ;; Vdrop = 160mV
CompanySipex Corporation
DatasheetDownload SP6201EM5-3.3/TR datasheet
Cross ref.Similar parts: LM3490, LP2980-N, LP2981-33, LP2981-N, LP2981A-33, LP2982, LP2985-33, LP2985-N, LP2985A-33, LP2992
Quote
Find where to buy
 
  

 

Features, Applications

FEATURES

Low Dropout Voltage: @ 100mA High Output Voltage Accuracy: 2% Guaranteed 200mA Output: SP6201 Ultra Low Shutdown Current: 1A Max Ultra Low GND Current @ 200mA Load @ 100A Load Fast Transient Response 78dB PSRR 100Hz 40dB PSRR @ 400kHz Extremely Tight Load and Line Regulation Very Low Temperature Coefficient Current and Thermal Limiting RESET Output (VOUT good) Logic-Controlled Electronic Enable Unconditionally Stable with 1F Ceramic 5 Pin SOT-23 Package Fixed Outputs 3.5V, 5V Adjustable Output Available

APPLICATIONS

Cellular Telephones Laptop, Notebooks and Palmtop Computers Battery-Powered Equipment Consumer/ Personal Electronics SMPS Post-Regulator DC-to-DC Modules Medical Devices Data Cable Pagers

DESCRIPTION

The SP6200 and SP6201 are CMOS LDOs designed to meet a broad range of applications that require accuracy, speed and ease of use. These LDOs offer extremely low quiescent current which only increases slightly under load, thus providing advantages in ground current performance over bipolar LDOs. The LDOs handle an extremely wide load range and guarantee stability with a 1F ceramic output capacitor. They have excellent low frequency PSRR, not found in other CMOS LDOs and thus offer exceptional Line Regulation. High frequency PSRR is better than to 400kHz. Load Regulation is excellent and temperature stability is comparable to bipolar LDOs. An enable feature is provided on all versions. The SP6200/6201 is available in fixed and adjustable output voltage versions in a small SOT-23-5 package. A VOUT good indicator is provided on all fixed output versions.

These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Supply Input Voltage (VIN)............................. to 7V Output Voltage (VOUT)......................... -0.6 to (VIN +1V) Enable Input Voltage (VEN)............................ to 7V Power Dissipation (PD).......... Internally Limited, Note 3 Lead Temperature (soldering 5s)....................... 260C Storage Temperature........................ to +150C

Input Voltage to +6V Enable Input Voltage to +6V Junction Temperature to +125C Thermal Resistance, SOT-23-5 (JA)................Note 3

VIN = VOUT = 5V for ADJ, = 100A, CIN = 1.0F, COUT 25C , unless otherwise specified. The denotes the specifications which apply over the full operating temperature range, unless otherwise specified.

PARAMETER Output Voltage Accuracy, (VO) Reference Voltage Output Voltage Temperature Coefficient, Note 4, (VO/T) Minimum Supply Voltage

CONDITIONS Variation from specified VOUT Adjustable version only

= 100mA VIN = (VOUT to 100mA, VIN to 100mA, VIN 200mA, SP6201 Only VEN 100mA, SP6200 only VEN 200mA, SP6201 Only Frequency IL =10mA Frequency SP6200 SP6201 Turns On Turns Off VEN 0.4V VEN = 100A

Line Regulation, (VO/ VIN) Load Regulation, Note 5, (VO / VO) SP6200-1.8V Load Regulation SP6200-1.5V Load Regulation Dropout Voltage, Note 6, (VIN VO)

Shutdown Quiescent Current, (IGND) Ground Pin Current, Note 7, (IGND)
Power Supply Rejection Ratio, (PSRR) Current Limit, (ICL) Thermal Limit 100 300

VIN = VOUT = 5V for ADJ, = 100A, CIN = 1.0F, COUT 25C , unless otherwise specified. The denotes the specifications which apply over the full operating temperature range, unless otherwise specified.

PARAMETER Thermal Regulation, Note 8, (VO/PD) Output Noise, (e no)

150 ENABLE INPUT Enable Input Logic-Low Voltage, (VIL) Enable Input Logic-High Voltage, (VIH) Enable Input Current, (IIL), (IIH) Reset Not Output

1F 0.1F from VOUT to Adj. to 100kHz Regulator Shutdown Regulator Enabled VIL < 0.4V VIH > 2.0V Threshold

Note 1. Exceeding the absolute maximum rating may damage the device. Note 2. The device is not guaranteed to function outside its operating rating. Note 3. The maximum allowable power dissipation at any TA (ambient temperature) is PD (MAX) = (TJ (MAX) TA) / A. Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. The JA of the SP6200/6201 (all versions) is 220C/W mounted a PC board with minimum copper area (see "Thermal Considerations" section for further details). Note 4. Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. Note 5. Load Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range; from 100mA, SP6200; from 200mA, SP6201. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Not applicable to output voltages less than 2.5V. Note 6. Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. Not applicable to output voltages less than 2.7V. Note 7. Ground pin current is the regulator quiescent current. The total current drawn from the supply is the sum of the load current plus the ground pin current. Note 8. Thermal regulation is defined as the change in output voltage at a time "t" after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 100mA load pulse at VIN = 6V for = 10ms.


 

Related products with the same datasheet
SP6200-3.3
SP6200EM5-1.5
SP6200EM5-1.5/TR
SP6200EM5-1.8
SP6200EM5-1.8/TR
SP6200EM5-2.5
SP6200EM5-2.5/TR
SP6200EM5-2.7
SP6200EM5-2.7/TR
SP6200EM5-2.85
SP6200EM5-2.85/TR
SP6200EM5-3.0
Some Part number from the same manufacture Sipex Corporation
SP6201EM5-3.5 Iout = 100mA ;; Vin Min. = 2.5V ;; Vin Max. = 7V ;; Iq = 28µA ;; Acc = 2% ;; Vdrop = 160mV
SP6201EM5-3.5/TR Micropower 100mA And 200mA CMOS LDO Regulators
SP6201EM5-5.0
SP6201EM5-5.0/TR
SP6201EM5-ADJ
SP6201EM5ADJ
SP6203 Iout = 300mA ;; Vin Min. = 2.7V ;; Vin Max. = 6V ;; Iq = 45µA ;; Acc = 2% ;; Vdrop = 180mV
SP6213 Iout = 100mA ;; Vin Min. = 2.5V ;; Vin Max. = 7V ;; Iq = 65µA ;; Acc = 2.50% ;; Vdrop = 250mV
SP6213EC3-2.5 SC-70 100mA CMOS LDO Regulator
SP6213EC5-1.8 Iout = 100mA ;; Vin Min. = 2.5V ;; Vin Max. = 7V ;; Iq = 65µA ;; Acc = 2.50% ;; Vdrop = 250mV
SP6231 Iout = 500mA ;; Vin Min. = 0.3V ;; Vin Max. = 7V ;; Iq = 400µA ;; Acc = 3% ;; Vdrop = 300mV
SP6231EN-3.3 500mA 3.3V Linear Regulator With Auxiliary Backup
SP6231EN-3.3/TR
SP6231ER-3.3 Iout = 500mA ;; Vin Min. = 0.3V ;; Vin Max. = 7V ;; Iq = 400µA ;; Acc = 3% ;; Vdrop = 300mV
SP6242EU Single Alkaline Cell,highefficiency Step-up DC-DC Converter
SP6243EU
SP6639
SP6639CN
SP6639CP
SP6640
SP6640CN

SP432CN : High Speed Low Power Quad RS-422 Differential Line Receiver

SP805RCP : 3V Supervisors iq = 40µA ;; Vin Min. = 1V ;; Vin Max. = 5.5V ;; Reset Threshold = 2.625V ;; Reset Active = Low ;; Reset Acc = 75mV ;; Package = 8 Pin Nsoic 8 Pin Pdip

SPX2815U-2.5 : Iout = 1.5A ;; Vin Min. = 2.75V ;; Vin Max. = 10V ;; Iq = 4mA ;; Acc = 1%, 2% ;; Vdrop = 1.1V

SPX2946U3-3.3 : 500ma Low Drop Out Voltage Regulator With Shutdown

SP6659EK1-L-1-8/TR : Buck 1.5MHz, 600mA Synchronous Buck Regulator # 94% Efficiency Possible # 600mA Output Current at VI= 3.6V # 2.5V to 5.5V Input Voltage Range # 1.5MHz constant frequency operation # No Schottky Diode Required

SP2525A-2EN : 3.0V to +5.5V USB Power Control Switch (Active Low) * +3.0V to +5.5V Input Voltage Range * 500mA Continuous Load Current per Channel * 2.6V Under-voltage Lockout * 1.25A Short Circuit Current Limit * 100mΩ Maximum On-Resistance * 75A On-State Supply Current

SP8064DG : High Speed, 10 Channel PDIC Features * Dual wavelength 650nm and 780nm * Data channel bandwidth 120 MHz (-3dB) * Eight selectable gain settings * Group delay error less than 0.5ns up to 72MHz * 6ns settling time * 16-pin Optical Land Grid Array (OPLGA) package

SP6686ER : 400mA Buck/Boost Charge Pump LED Driver Features * Output Current up to 400mA * Up to 94% Efficiency in Torch Mode * Automatic Softstart limits inrush current * Adjustable FLASH mode * x1 and x2 Automatic Modes for High Efficiency * Minimum External Components: No In

SPX1581T5/TR : 3A Low Dropout Voltage Regulator

SP3080EEN : Advanced-failsafe Rs-485/rs-422 Transceiver 1/8th Unit Load, Slew-limited, 15kv Esd-protected

SPX29151U5-1-8 : 1.5A Low Dropout Voltage Regulator

SP301CS : Rs-232/rs-422 Line Drivers/receivers

 
0-C     D-L     M-R     S-Z