Details, datasheet, quote on part number: SK10E151PJT
PartSK10E151PJT
CategoryLogic => Registers
Description6-Bit D Register
CompanySemtech Corporation
DatasheetDownload SK10E151PJT datasheet
  

 

Features, Applications

The SK10/100E151 offers 6 edge-triggered, high-speed, master-slave D-type flip-flops with differential outputs, designed for use in new high-performance ECL systems. This device is fully compatible with MC10E151 and MC100E151. The two external clock signals (CLK1, CLK2) are gated through a logical OR operation before use as clocking control for the flip-flops. Data is clocked into the flip-flops on the rising edge of either or CLK2 (or both). When both CLK1 and CLK2 are at a logic LOW, data enters the master and is transferred to the slave when either or CLK2 (or both) go HIGH. The MR (Master Reset) signal operates asynchronously to make all Q outputs to a logic LOW.

1100 MHz Toggle Frequency Extended 100E VEE Range to 5.5V Differential Outputs Asynchronous Master Reset Dual Clocks Internal 75K Input Pulldown Resistors ESD Protection of >4000V Fully Compatible with MC10/100E151 Specified Over Industrial Temperature Range: to +85oC Available in 28-Pin PLCC Package

Function Data Inputs Clock Inputs Master Reset True Outputs Inver ting Outputs Output VCC

Asynchronous Operation NOTES: H = HIGH Voltage Level L = LOW Voltage Level X = Don 't Care t = Time Before Positive CLK Transition t+1 = Time After Positive CLK Transition u = LOW-to-HIGH Transition


NOTES: 1. Datums -L-, -M-, and -N - determined where top of lead shoulder exits plastic body at mold parting line. 2. DIM G1, true position to be measured at Datum -T-, Seating Plane. 3. DIM R and U do not include mold flash. Allowable mold flash 0.010 (0.250) per side. 4. Dimensioning and tolerancing per ANSI 1982. 5. Controlling Dimension: Inch. 6. The package top may be smaller than the package bottom 0.012 (0.300). Dimensions R and U are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 7. Dimension H does not include Dambar protrusion or intrusion. The Dambar protrusion(s) shall not cause the H dimension to be greater than 0.037 (0.940). The Dambar intrusion(s) shall not cause the H dimension to be smaller than 0.025 (0.635).


 

Related products with the same datasheet
SK100E151PJ
SK100E151PJT
SK10E151
SK10E151PJ
Some Part number from the same manufacture Semtech Corporation
SK10E445 4-Bit Serial / Parallel Converter
SK10EL01W 4-Input or / Nor
SK10EL01WD 4-input or / Nor
SK10EL07 2-input Xor / Xnor
SK10EL11W 1:2 Differential Fanout Buffer
SK10EL11WD
SK10EL12W Low Impedance Driver
SK10EL14W 1:5 Clock Distribution
SK10EL14WD 1:5 Clock Distribution Chip
SK10EL15W 1:4 Clock Distribution
SK10EL15WD
SK10EL16B
SK10EL16TA-TD Differential Receiver
SK10EL16V Differential Receiver With Variable Output Swing
SK10EL16VD Differential Receiver
SK10EL16W
SK10EL16X
SK10EL16XWA High-gain Differential Receiver
SK10EL17W
SK10EL31W
SK10EL32W

1N6103 : 500 W Axial Bi-polarity Transient Voltage Suppressors

EZ1900CS : Regulator Balance Controller

SCDAS2 : Standard Recovery Doubler And Center Taps

ZJ4V7B : Silicon Epitaxial Planer Zener Diodes

SDB310WAUF : Schottky Barrier Diode

3530EN103K7 : HIGH Voltage Capacitors Monolithic Ceramic TYPE

6666DN103Z8 : HIGH Voltage Capacitors Monolithic Ceramic TYPE

JANTX1N6156AUS : 1500 W, UNIDIRECTIONAL, SILICON, TVS DIODE Specifications: Configuration: Single ; Direction: Unidirectional ; Package: HERMETIC SEALED PACKAGE-2 ; Pin Count: 2 ; Number of Diodes: 1 ; VBR: 6.12 volts

SC11240CSKTR : 4 V FIXED POSITIVE LDO REGULATOR, 0.275 V DROPOUT, PDSO6 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, SOT-23, 6 PIN ; Life Cycle Stage: ACTIVE ; Output Voltage: 3.88 to 4.12 volts ; IOUT: 0.1500 amps ; VIN: 5 to 10 volts ; Dropout Voltage: 0.2750 volts

 
0-C     D-L     M-R     S-Z