Details, datasheet, quote on part number: OD-F8HS17CS
DescriptionPrecision Sc-cut OCXO in 20x20 mm Through Hole Package
CompanyNEL Frequency Controls Inc.
DatasheetDownload OD-F8HS17CS datasheet


Features, Applications

OD-X8HXXXXX Precision SC-cut OCXO 20x20 mm Through Hole Package

SC-cut crystal -9 High Stability (up 5x10 ) Low Aging (5x10 /day, 5x10 /year) Low Phase Noise (-160 dBc/Hz, TYP, floor) Sine Wave or HCMOS/TTL output 4.8 MHz to 160 MHz Frequencies Available


357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email:

Parameter Symb Absolute Maximum Ratings Vcc Input Break Down Voltage Ts Storage temper. Vc Control Voltage Electrical F Frequency stability F/F Aging Allan Variance SSB Phase Noise Condition Min vs. Temp. vs. Supply per day per Hz 1 KHz 10 KHz After 30 minutes worst direction 1E-7 1E-11 Typ Max Unit °C V MHz ppb ppb/V

steady state, 25°C W Standard Operating steady state, -30°C Temperature, for Op start-up -30°C 3.2 Temp. ad 20% Subharmonics -45 dBc At Higher Frequencies Spectral Purity Spurious -80 Harmonics/Sine -30 10KOhm//15pF (HCMOS/TTL), 50 Ohm (Sinewave) Load to 0.1ppm accuracy 3 5 minutes 3 min. at 12V Warm-up time 3.3V HCMOS/TTL compatible or Sinewave (+7± 3) dBm -25dBm Harmonics at sine Output Waveform 4.0 V Control voltage from nominal ±0.5 ±1 ppm Pull range Monotonic, posit 0.4 ppm/V Deviation slope Vc0 @25°C, Fnom. 3.0 V Setability Environmental and Mechanical to 70°C Standard, Other options ­ see chart below Operating temp. range Per 30G, 11ms Mechanical Shock Per 2000 Hz Vibration 260°C for 10s Max leads only Soldering Conditions Electrical Connections Pin Pin#2 ­ Vref; Pin #3 ­ Vcc; Pin #4- Output ; Pin #5- GND; Pin Out Power consumption

Notes: 1* Higher frequencies can be achieved either by using higher frequency crystals or by low noise analog harmonic multiplication. Both methods have advantages and drawbacks. If lowest possible phase noise on the noise floor is most important ­ high frequency crystal will be used. If phase noise close to the carrier and aging are more important ­ multiplication will be used. Please consult factory for your specific requirement. 2* Aging rate is usually proportional to the operating frequency, unless higher frequency is achieved by multiplication. Keep it in mind while specifying aging. 3* Phase noise deteriorates with frequencies going higher. If analog multiplication is used to achieve higher frequency the phase noise roughly follows the formula of additional 20LogN, where is a multiplication factor across entire frequency offset range. If higher frequency is achieved by using higher frequency crystal phase noise close to the carrier deteriorates due to the lower Q of the crystal and is usually worse, compared to multiplied solution. On the noise floor, however it remains more or less the same. This design usually starts utilizing multiplication techniques in the range of 25 MHz to 35 MHz.


Related products with the same datasheet
Some Part number from the same manufacture NEL Frequency Controls Inc.
OD-F8HS17DL Precision Sc-cut OCXO in 20x20 mm Through Hole Package

HS2830 : XO XO ECL Oscillators Thru-hole Leaded 4 Pin (14 PIN) Frequency Range (Mhz) : 15.0 - 250.0 Output/input : Differential, -4.5V

SMA2840 : 3.3 V, +/-100 Ppm, Ecl Crystal Clock Oscillator

OD-F8HS59AS : Precision Sc-cut OCXO in 20x20 mm Through Hole Package


OD-A8HS18CS : Precision Sc-cut OCXO in 20x20 mm Through Hole Package

OE-08HS28ES : Precision Sc-cut OCXO in 36x27 mm ˇ°europackˇ±

OE-F8HT17FP : Precision Sc-cut OCXO in 36x27 mm ˇ°europackˇ±

OF-08HT28DP : Precision Sc-cut OCXO in 25x22 mm Low Profile SMD Package

PJ-A3670-184.0 : VCXO Series (pecl)

0-C     D-L     M-R     S-Z