Details, datasheet, quote on part number: XC68C812A4PV5B1
CategoryMicrocontrollers => 16 bit => M68HC12 Family
TitleM68HC12 Family
DescriptionTechnical Suppliment Document Covering The 3 V Version of The 812A4.
CompanyMotorola Semiconductor Products
DatasheetDownload XC68C812A4PV5B1 datasheet


Features, Applications

The MC68C812A4 is the low-voltage version of the standard MC68HC812A4 microcontroller unit (MCU), a 16-bit device composed of standard on-chip peripheral modules connected by an intermodule bus. Modules include a 16-bit central processing unit (CPU12), a Lite integration module (LIM), two asynchronous serial communications interfaces (SCI0 and SCI1), a serial peripheral interface (SPI), a timer and pulse accumulation module, an 8-bit analog-to-digital converter (ATD), 1-Kbyte RAM, 4-Kbyte EEPROM, and memory expansion logic with chip selects, key wakeup ports, and a phase-locked loop (PLL). This supplement contains the most accurate electrical information for the MC68C812A4 microcontroller available at the time of publication. The information should be considered preliminary and is subject to change. The following characteristics are contained in this document: Table 1 Maximum Ratings Table 2 Thermal Characteristics Table 3 DC Electrical Characteristics Table 4 Supply Current Table 5 ATD Maximum Ratings Table 6 ATD DC Electrical Characteristics Table 7 Analog Converter Characteristics (Operating) Table 8 ATD AC Characteristics (Operating) Table 9 EEPROM Characteristics Table 10 Control Timing Table 11 Peripheral Port Timing Table 12 Non-Multiplexed Expansion Bus Timing Table 13 SPI Timing

Rating Supply voltage Input voltage Operating temperature range MC68C812A4PV5 Storage temperature range Current drain per pin3 Excluding VDD and VSS VDD differential voltage


NOTES: 1. Permanent damage can occur if maximum ratings are exceeded. Exposures to voltages or currents in excess of recommended values affects device reliability. Device modules may not operate normally while being exposed to electrical extremes. 2. Refer to MC68HC812A4TS/D Technical Summary for complete part numbers. 3. One pin at a time, observing maximum power dissipation limits. Internal circuitry protects the inputs against damage caused by high static voltages or electric fields; however, normal precautions are necessary to avoid application of any voltage higher than maximum-rated voltages to this highimpedance circuit. Extended operation at the maximum ratings can adversely affect device reliability. Tying unused inputs to an appropriate logic voltage level (either GND or VDD) enhances reliability of operation.

Characteristic Average junction temperature Ambient temperature Package thermal resistance (junction-to-ambient) 112-pin thin quad flat pack (TQFP) Symbol TA JA Value TA + (PD JA) User-determined 39 PINT + PI/O or K ------------------------T C IDD VDD User-determined PD (TA PD2 Unit C C/W

NOTES: 1. This is an approximate value, neglecting PI/O. 2. For most applications PI/O PINT and can be neglected. is a constant pertaining to the device. Solve for K with a known TA and a measured PD (at equilibrium). Use this value K to solve for PD and TJ iteratively for any value of TA.

Table 3 DC Electrical Characteristics VDD = 3.3 Vdc 0.3V, VSS = 0 Vdc, TL to TH, unless otherwise noted

Characteristic Input high voltage, all inputs Input low voltage, all inputs Output high voltage All I/O and output pins Normal drive strength IOH -10.0 A IOH -0.8 mA Reduced drive strength IOH -4.0 A IOH -0.3 mA Output low voltage, All I/O and output pins, normal drive strength IOL 10.0 A IOL 1.6 mA VOL EXTAL, PAD[7:0], VRH, VRL, VFP, XIRQ, reduced drive strength IOL 3.6 A IOL 0.6 mA Input leakage current1 all inputs except IRQ, PAD7, and XFC Vin = VDD or VSS IRQ, PAD7, XFC Three-state leakage, I/O ports, BKGD, and RESET Input capacitance All input pins and ATD pins (non-sampling) ATD pins (sampling) All I/O pins Output load capacitance All outputs except PS[7:4] Active pull-up, pull-down current IRQ, XIRQ, ECLK, LSTRB, R/W , BKGD, MODA, MODB, ARST Ports S, T RAM standby voltage, power down RAM standby current Iin IOZ V mA Symbol VIH VIL Min 0.7 VDD VSS-0.3 Max VDD Unit V

NOTES: 1. Specification is for parts in the to +70C range. Higher temperature ranges will result in increased current leakage.


Related products with the same datasheet
Some Part number from the same manufacture Motorola Semiconductor Products
XC68HC08AZ0CPU MC68HC08AZ0 Advance Information
XC68HC08AZ32CFU MC68HC08AZ32 Advance Information
XC68HC12D60CFU8 MC68HC12D60, MC68HC912D60 Advance Information
XC68HC705F32FU 68HC705F32, 68HC05F32 Technical Data Book
XC68HC705JB3JP 68HC05JB3 And 68HC705JB3 General Release Specification
XC68HC705JJ7CP MC68HC705JJ7, MC68HC705JP7, MC68HC705SJ7, MC68HC705SP7, MC68HRC705JJ7, MC68HRC705JP7 Advance Information
XC68HC705X32CFU4 68HC05X16, 68HC05X32, 68HC705X32 Technical Data Book
XC68HC705X4CDW MC68HC(7)05X4 Technical Data
XC68HC708KH12FU 68HC08KH12, 68HC708KH12 Advance Information
XC68HC708MP16MFU MC68HC12D60, MC68HC912D60 Advance Information
XC68HC711D3CFS2 MC68HC711D3 Technical Data
XC68HC711E20CFS2 M68HC11E/D M68HC11E Family Technical Data
XC68HC711K4CFS3 M68HC11K Family Technical Data
XC68HC711KS2CFS4 M68HC11E/D M68HC11E Family Technical Data
XC68HC711P2CFS3 MC68HC(7)11P2 Technical Data

68HC908QF1 : Microcontroller

BRY55-60 : SCRS 0.8 Ampere RMS 30 to 600 Volts

M68332BCC :

MHPM7A15A60A :

MHW9188 : MHW9188 870 Mhz, 20.3 DB Gain, 132-Channel GAAS Catv Amplifier Module

MJF2955 : Comlementery Silicon Power Transistor

MRFA2600 : RF Power Amplifier

MRF5S4140HSR3 : N-channel Enhancement-mode Lateral Mosfets

S908QC8MDSER : Microcontrollers


0-C     D-L     M-R     S-Z