|Category||Power Management => Supervisory Circuits => Microprocessor Supervisors => General Purpose|
|Description||6-Pin P Reset Circuit With Power-fail Comparator|
|Company||Maxim Integrated Products|
|Datasheet||Download MAX6343 datasheet
The MAX6342MAX6345 family of microprocessor (µP) supervisory circuits monitors power supplies in digital systems. These devices significantly improve system reliability and accuracy compared to separate ICs or discrete components. The MAX6342MAX6345 provide factory-trimmed VCC reset threshold voltages from to 4.63V and operate with supply voltages between +1V and A +1.25V threshold detector allows for a power-fail warning, for low-battery detection, or for monitoring another power supply. The MAX6342 contains an MR input and an active-low push-pull reset. The MAX6343 and MAX6344 are identical to the MAX6342 except they provide an active-low, open-drain reset and an active-high, pushpull reset, respectively. The MAX6345 provides a second reset output in place of the MR input to give it an activehigh push-pull reset and an active-low push-pull reset. All of the devices are packaged in a miniature SOT23. o Small 6-Pin SOT23 Package o Precision Factory-Set VCC Reset Thresholds Between 2.33V and 4.63V o Guaranteed RESET Valid to VCC o 100ms min Reset Pulse Width o Debounced CMOS-Compatible Manual-Reset Input o Voltage Monitor for Power-Fail or Low-Battery WarningFeatures
Portable Computers Telecom Equipment Networking Equipment Portable/Battery-Powered Equipment Multivoltage Systems Embedded Control Systems
Note: The MAX6342MAX6345 are available with factory-set reset thresholds from to 4.63V (see Selector Guides 1, 2). Insert the letter corresponding to the desired nominal reset threshold into the blank following the part number. There a 2500 piece order increment required for the SOT package. SOT Top Marks table appears at end of data sheet.Typical Operating Circuit appears at end of data sheet.
PART MAX6344 MAX6345 PUSH-PULL RESET OUTPUT OPEN-DRAIN RESET OUTPUT PUSH-PULL RESET OUTPUT MANUAL-RESET INPUT 1
For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800. For small orders, phone 1-800-835-8769.
VCC to +6V RESET, RESET -0.3V to (VCC + 0.3V) RESET to +6V MR, PFI, PFO..............................................-0.3V to (VCC + 0.3V) Input Current, VCC..............................................................50mA Output Current, RESET, RESET..........................................50mA Continuous Power Dissipation (TA 6-Pin SOT23 (derate 4mW/°C above +70°C).............320mW Operating Temperature to +125°C Junction Temperature......................................................+150°C Storage Temperature to +150°C Lead Temperature Range (soldering, 10s)..................... +300°C
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
(VCC to +125°C, unless otherwise noted. Typical values are = +25°C and VCC = +3V.) (Note 1) PARAMETER Supply Voltage Range SYMBOL VCC to +125°C VCC to +85°C VCC +85°C No load VCC to +125°C VCC to +125°C VCC = VTH to (VTH - 100mV) VCC > 1.2V, ISINK = 100µA VCC > 2.7V, ISINK = 1.2mA VCC > 4.5V, ISINK = 3.2mA VCC > 1.2V, ISOURCE = 50µA VCC > 2.7V, ISOURCE 500µA (MAX6342/MAX6345 only) VCC > 4.5V, ISOURCE 800µA (MAX6342/MAX6345 only) CONDITIONS MIN TYP MAX VCC 0.8 VCC 0.8 VCC V UNITS VVCC to Reset Delay VOL RESET and RESET Outputs Drive Capability (Note 2) VOH
(VCC to +125°C, unless otherwise noted. Typical values are = +25°C and VCC = +3V.) (Note 1) PARAMETER Reset Timeout Period Open-Drain RESET Output Leakage Current (Note 3) MR Input Low MR Input High MR Pull-Up Resistance MR Minimum Pulse Width MR Glitch Rejection MR to Reset Delay PFI Input Threshold PFI Leakage Current (Note 3) PFO Output Voltage PFO Output Voltage PFO Output Short-Circuit Current PFI to PFO Delay VOL VOH to +125°C VCC = 4.5V, ISINK = 3.2mA VCC = 4.5V, ISOURCE = 800µA Output sink current Output source current VOVERDRIVE 15mV 0.8 VCC SYMBOL tRP ILKG VIL VIH 0.7 VCC CONDITIONS +125°C MAX6343 only, VCC > VTH(MAX) MIN 100 80 TYP 180 MAX VCC UNITS mA µs
Note 1: Overtemperature limits are guaranteed by design and not production tested. Note 2: Apply to each part in accordance with threshold voltage, output configuration, and manual reset status selected. Note 3: Leakage parameters are guaranteed by design and not production tested.
VCC 5V 25 SUPPLY CURRENT (µA) VCC 15 10 VCC 1V 1sec/div TEMPERATURE (°C) VCC 2.5V 1V/div RESET 0 RESET 1V/div
|Related products with the same datasheet|
|Some Part number from the same manufacture Maxim Integrated Products|
|MAX6343_UT-T 6-Pin P Reset Circuit With Power-fail Comparator|
|MAX6346 3-Pin, Ultra-low-power SC70/SOT P Reset Circuits|
|MAX6346UR__-T 3-pin, Ultra-low-power Sc70/sot Reset Circuits|
|MAX6347 3-Pin, Ultra-low-power SC70/SOT P Reset Circuits|
|MAX6347UR__-T 3-pin, Ultra-low-power Sc70/sot Reset Circuits|
|MAX6348 3-Pin, Ultra-low-power SC70/SOT P Reset Circuits|
MAX1137 : 2.7V to 3.6V And 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCs
MAX166AEWP : 5 s, 8-Bit ADC With Track/hold And Reference
MAX2265EUE : 2.7v, Single-supply, Cellular-band Linear Power Amplifiers
MAX4051A : Low-Voltage, CMOS Analog Multiplexers/switches
MXL1014C : Dual/Quad, Precision op Amps
MAX9877AERP : Low RF Susceptibility, Mono Audio Subsystem With DirectDrive Headphone Amplifier The MAX9877A combines a high-efficiency Class D audio power amplifier with a stereo Class AB capacitorless DirectDrive® headphone amplifier. Maxim\'s 3rd generation, filterless Class D amplifier with active emissions l
ICL7614CCSA : Single/dual/triple/quad Operational Amplifiers
Z86L9808PSG : 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO28 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 8 MHz ; ROM Type: MROM ; Supply Voltage: 2 to 3.6 volts ; I/O Ports: 23 ; Package Type: SSOP, Other, LEAD FREE, SSOP-28 ; Operating Range: Commercial ; Pin Count: 28 ; Operating Temperature: 0 to 70 C (32 to 158 F)
5962-8967901QX : 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CQCC44 Specifications: Package Type: LCCC, CERAMIC, LCC-44 ; Screening Level: Military ; Pins: 44 ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Sample Rate: 55.6 kSamples/Sec ; Input Voltage: -4.5 to 4.52 volts