Details, datasheet, quote on part number: LTC1149
PartLTC1149
CategoryPower Management => Regulators => Switching Regulators => Step-Down
TitleStep-Down
DescriptionLTC1149, 48V Synchronous Step-down
CompanyLinear Technology Corporation
DatasheetDownload LTC1149 datasheet
Quote
Find where to buy
 
  

 

Features, Applications
LTC1149 LTC1149-3.3/LTC1149-5 High Efficiency Synchronous Step-Down Switching Regulators FEATURES

Operation to 48V Input Voltage Ultrahigh Efficiency: to 95% Current Mode Operation for Excellent Line and Load Transient Response High Efficiency Maintained over Wide Current Range Logic-Controlled Micropower Shutdown Short-Circuit Protection Very Low Dropout Operation: 100% Duty Cycle Synchronous FET Switching for High Efficiency Adaptive Nonoverlap Gate Drives Available in 16-Pin Narrow SO Package

The LTC 1149 series is a family of synchronous stepdown switching regulator controllers featuring automatic Burst ModeTM operation to maintain high efficiencies at low output currents. These devices drive external complementary power MOSFETs at switching frequencies to 250kHz using a constant off-time current-mode architecture. Special onboard regulation and level-shift circuitry allow operation at input voltages from dropout 48V (60V absolute max). The constant off-time architecture maintains constant ripple current in the inductor, easing the design of wide input range converters. Current mode operation provides excellent line and load transient response. The operating current level is user-programmable via an external current sense resistor. The LTC1149 series incorporates automatic power saving Burst Mode operation when load currents drop below the level required for continuous operation. Standby power is reduced to only about 8mW at VIN 12V. In shutdown, both MOSFETs are turned off.

Notebook and Palmtop Computers Portable Instruments Battery-Operated Digital Devices Industrial Power Distribution Avionics Systems Telecom Power Supplies

, LTC and LT are registered trademarks of Linear Technology Corporation. Burst Mode is a trademark of Linear Technology Corporation.

0V = NORMAL >2V = SHUTDOWN SHDN1 SHDN2 ITH CT SGND SENSE + SENSE NGATE P, RGNDS 1000pF

TOP VIEW PGATE VIN VCC PDRIVE VCC CT ITH SENSE CAP SHDN2 14 RGND 13 NGATE 12 PGND 11 SGND VFB SHDN1* 9 SENSE + S PACKAGE 16-LEAD PLASTIC SO

Input Supply Voltage (Pin to 60V VCC Output Current (Pin 3).................................. 50mA VCC Input Voltage (Pin 5)........................................ 16V Continuous Output Current (Pins 13).............. 50mA Sense Voltages (Pins 8, 9) VIN 0.3V VIN < 12.7V............................. (VCC 0.3V Shutdown Voltages (Pins 15)............................. 7V Operating Temperature Range.................... to 70C Extended Commercial Temperature Range............................... to 85C Junction Temperature (Note 1)............................ 125C Storage Temperature Range................ to 150C Lead Temperature (Soldering, 10 sec)................. 300C

Consult factory for Industrial and Military grade parts.

SYMBOL V10 I10 VOUT PARAMETER Feedback Voltage (LTC1149 Only) Feedback Current (LTC1149 Only) Regulated Output Voltage LTC1149-3.3 LTC1149-5 Output Voltage Line Regulation Output Voltage Load Regulation LTC1149-3.3 LTC1149-5 Burst Mode Output Ripple I2 Input DC Supply Current (Note 3) Normal Mode Burst Mode Shutdown VCC V3 VIN V1 Internal Regulator Voltage (Sets MOSFET Gate Drive Levels) VCC Dropout Voltage P-Gate to Source Voltage (Off) VIN = 9V

VIN = 9V ILOAD = 700mA ILOAD = 700mA VIN to 48V, ILOAD 5mA < ILOAD 5mA < ILOAD < 2A ILOAD = 0A VIN = 12V VIN = 48V VIN = 12V VIN = 48V VIN = 2V VIN = 2V VIN = 20mA VIN = 10mA VIN = 12V VIN = 48V

SYMBOL V8 PARAMETER Current Sense Threshold Voltage I15 I6 tOFF tr, tf Shutdown 1 Threshold LTC1149-3.3, LTC1149-5 Shutdown 2 Threshold Shutdown 2 Input Current CT Pin Discharge Current Off-Time (Note 4) Driver Output Transition Times = 5V

CONDITIONS = 1.32V (Forced) V8 = VOUT = 3.5V (Forced) V8 = VOUT = 5.3V (Forced) V8 = VOUT 100mV
VOUT In Regulation, VSENSE = VOUT = 390pF, ILOAD = 3000pF (Pins 4, 13), VIN = 6V

SYMBOL V10 VOUT PARAMETER Feedback Voltage LTC1149 Only Regulated Output Voltage LTC1149-3.3 LTC1149-5 Input DC Supply Current (Note 3) Normal Mode Burst Mode Shutdown VCC 8 V15 tOFF Internal Regulator Voltage (Sets MOSFET Gate Drive Levels) Current Sense Threshold Voltage Shutdown 2 Threshold Off-Time (Note = 390pF, ILOAD = 700mA, VIN = 10V VIN = 9V ILOAD = 700mA ILOAD = 700mA VIN = 12V VIN = 48V VIN = 12V VIN = 48V VIN = 2V VIN = 2V VIN = 20mA Low Threshold (Forced) High Threshold (Forced) 9.75 CONDITIONS MIN 3.17 4.85 TYP MAX UNITS V s

The q denotes specifications which apply over the full operating temperature range. Note TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formulas: TA + (PD + (PD)(110C/W) Note 2: Pin is a shutdown pin on the LTC1149-3.3 and LTC1149-5 fixed output voltage versions and must be at ground potential for testing.

Note 3: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. The allowable operating frequency may be limited by power dissipation at high input voltages. See Typical Performance Characteristics and Applications Information. Note 4: In applications where RSENSE is placed at ground potential, the offtime increases approximately 40%. Note 5: The LTC1149, LTC1149-3.3, and LTC1149-5 are not tested and not quality assurance sampled 40C and 85C. These specifications are guaranteed by design and/or correlation.


 

Related products with the same datasheet
LTC1149-3.3
LTC1149-5
LTC1149CN
LTC1149CN-3.3
LTC1149CN-5
LTC1149CS
LTC1149CS-3.3
LTC1149CS-5
LTC1149CS-3.3#TR
LTC1149CN-3.3#PBF
LTC1149CS-3.3#PBF
LTC1149CS-3.3#TRPBF
Some Part number from the same manufacture Linear Technology Corporation
LTC1149-3.3 LTC1149, 48V Synchronous Step-down
LTC1150 LTC1150, 15V Zero-drift Operational Amplifier With Internal Capacitors
LTC1151 LTC1151, Dual 15V Zero-drift Operational Amplifier
LTC1151CSW Dual 15V Zero-drift Operational Amplifier
LTC1152 LTC1152, Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1152C Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1152CN8 LTC1152, Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1152I Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1152IN8 LTC1152, Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1153 LTC1153, Auto-reset Electronic Circuit Breaker
LTC1153IN8 Auto-reset Electronic Circuit Breaker
LTC1154 LTC1154, High-side Micropower MOSFET Driver
LTC1155 LTC1155, Dual High Side Micropower N-Ch. MOSFET Driver With Internal Charge Pump
LTC1155C Dual High Side Micropower MOSFET Driver
LTC1155CJ8 LTC1155, Dual High Side Micropower N-Ch. MOSFET Driver With Internal Charge Pump
LTC1155I Dual High Side Micropower MOSFET Driver
LTC1155IN8 LTC1155, Dual High Side Micropower N-Ch. MOSFET Driver With Internal Charge Pump
LTC1156 LTC1156, Quad High Side Micropower N-Ch. MOSFET Driver With Internal Charge Pump
LTC1156C Quad High Side Micropower MOSFET Driver With Internal Charge Pump
LTC1156CN LTC1156, Quad High Side Micropower N-Ch. MOSFET Driver With Internal Charge Pump
LTC1156CSW Quad High Side Micropower MOSFET Driver With Internal Charge Pump

LTC1164-8CSW : Low Power, Low Noise, Quad Universal Filter Building Block

LTC3535EDD-PBF : 2.2 MHz, 600ma Synchronous Step-up Dc/dc Converter and 100ma LDO

LTC3109IGN#TRPBF : Pmic - Power Management - Specialized Integrated Circuit (ics) Tape & Reel (TR) 6mA 30mV ~ 500mV; IC BOOST CONVERTER PMU 20SSOP Specifications: Applications: Energy Harvesting ; Current - Supply: 6mA ; Voltage - Supply: 30mV ~ 500mV ; Package / Case: 20-SSOP (0.154", 3.90mm Width) ; Packaging: Tape & Reel (TR) ; Operating Temperature: -40C ~ 125C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

LTC3803MPS6#TRPBF : Pmic - Voltage Regulator - Dc Dc Switching Controller Integrated Circuit (ics) Current Mode Tape & Reel (TR) 1 5.7 V ~ 8 V; IC FLYBACK ADJ 1A TSOT23-6 Specifications: PWM Type: Current Mode ; Number of Outputs: 1 ; Package / Case: SOT-23-6 Thin, TSOT-23-6 ; Packaging: Tape & Reel (TR) ; Duty Cycle: 90% ; Voltage - Supply: 5.7 V ~ 8 V ; Frequency - Max: 240kHz ; Buck: No ; Boost: No ; Flyback: Yes ; Inverting: No ; Doubler: No ; Divider: No ; C

LT1219CS8#TR : Linear - Amplifier - Instrumentation, Op Amps, Buffer Amp Integrated Circuit (ics) General Purpose Tape & Reel (TR) 425A 2 V ~ 30 V, 1 V ~ 15 V; IC OPAMP PREC R-R I/O 15V 8SOIC Specifications: Packaging: Tape & Reel (TR) ; Amplifier Type: General Purpose ; Number of Circuits: 1 ; Package / Case: 8-SOIC (0.154", 3.90mm Width) ; Slew Rate: 0.05 V/s ; Gain Bandwidth Product: 150kHz ; Current - Supply: 425A ; Current - Output / Channel: 20mA ; Voltage - Supply, Single/Du

LT1237CSW#TR : Interface - Drivers, Receivers, Transceiver Integrated Circuit (ics) Transceiver Tape & Reel (TR) 4.5 V ~ 5.5 V; IC TXRX 5V RS232 ADV LOPWR28SOIC Specifications: Number of Drivers/Receivers: 3/5 ; Type: Transceiver ; Voltage - Supply: 4.5 V ~ 5.5 V ; Package / Case: 28-SOIC (0.295", 7.50mm Width) ; Packaging: Tape & Reel (TR) ; Protocol: RS232 ; Lead Free Status: Contains Lead ; RoHS Status: RoHS Non-Compliant

LT1634AIS8-2.5 : 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.25 V, PDSO8 Specifications: Package Type: Other, 0.150 INCH, LEAD FREE, PLASTIC, SOP-8 ; VREF: 1.25 to 1.25 volts ; TC: 10 ppm/C ; Operating Temperature: 0 to 70 C (32 to 158 F)

LTC2255CUHTR : 1-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC32 Specifications: Package Type: 5 X 5 MM, PLASTIC, MO-220-WHHD, QFN-32 ; Screening Level: Commercial ; Pins: 32 ; Operating Temperature: 0.0 to 70 C (32 to 158 F) ; Sample Rate: 125000 kSamples/Sec ; Input Voltage: -1 to 1 volts

Same catergory

AKBPC603 : 6 Amp Controlled Avalanche Silicon Bridge Rectifier.

L2750 : Power Controllers & Motor Drivers. Dual Low Drop High Power Operational Amplifier.

L6228 : Power Controllers & Motor Drivers. Dmos Driver For Bipolar Stepper Motor.

LM2575S : 1a & 3a Miniconverter Switching Regulators. The LM2575/6 series switching regulators are monolithic integrated circuits designed for use in buck or buck/ boost regulator applications requiring accurate output voltages over combined variations of line, load and temperature. This unique series greatly simplifies switching power supply design. The LM2575 has a maximum output current of 1A and the LM2576.

MAX1570EVKIT : MAX1570EVKIT Evaluation Kit For The MAX1570. The MAX1570 evaluation kit (EV kit) is a fully assembled and tested surface-mount circuit board. The EV kit contains the MAX1570, a white LED driver with high-efficiency charge pump. The EV kit accepts to 5.5V input and drives up to five white LEDs with regulated constant current for uniform intensity. The MAX1570 runs at 1MHz fixed frequency, allowing.

MSK4250 : 75 V, 10A MOSFET H-bridge Brushed Motor Controller. 10 AMP, 75V, H-BRIDGE MOSFET BRUSHED MOTOR CONTROLLER 75 Volt Motor Supply Voltage 10 Amp Output Switch Capability 100% Duty Cycle High Side Conduction Capable Shoot-Through/Cross Conduction Protection "Real" Four Quadrant Torque Control Capability Good Accuracy Around the Null Torque Point The MSK is a complete H-bridge MOSFET Brushed Motor Control.

RN5VS : Low Voltage Detector.

RT9238 : Switching->VRM Specified. = Synchronous Buck With Triple Linear Controllers ;; Power in Voltage = 5V ;; Output Volt. Range = 1.05V V 1.825V 1.85V V 2.05V ;; VCC Voltage = 12V ;; Packages = SOP-28 ;; VRM = 8.4/8.5 ;;.

SG309R : 5 -volt Fixed Voltage Regulators. The is a completely self-contained 5V regulator. Designed to provide local regualtion at currents to 1A for digital logic cards, this device is available in the hermetic TO-66, TO39 and hermetic and plastic TO-220. A major feature of the SG109's design is its built-in protective which make it essentially blowout proof. These consist of both current.

TDE1897CDP : 0.5A High-side Driver Industrial Intelligent Power Switch. 0.5A HIGH-SIDE DRIVER INDUSTRIAL INTELLIGENT POWER SWITCH 0.5A OUTPUT CURRENT TO 35V SUPPLY VOLTAGE RANGE INTERNAL CURRENT LIMITING THERMAL SHUTDOWN OPEN GROUND PROTECTION INTERNAL NEGATIVE VOLTAGE CLAMPING - 45V FOR FAST DEMAGNETIZATION DIFFERENTIAL INPUTS WITH LARGE COMMON MODE RANGE AND THRESHOLD HYSTERESIS UNDERVOLTAGE LOCKOUT WITH HYSTERESIS OPEN.

TPS2310IPW : External FET. ti TPS2310, 3-13V Dual Hotswap ic w/ Inter-dependent Channel Circuit Breaking & PWR Good Report, Act-low Enable.

UC2824DW : Current Mode. ti UC2824, High Speed PWM Controller. Complementary Outputs Practical Operation Switching Frequencies 1MHz 50ns Propagation Delay to Output High Current Dual Totem Pole Outputs (1.5A Peak) Wide Bandwidth Error Amplifier Fully Latched Logic with Double Pulse Suppression Pulse-by-Pulse Current Limiting Soft Start / Max. Duty Cycle Control Under-Voltage Lockout with Hysteresis Low Start Up Current.

VRE405 : Output (V) = ±5.0 ;; Initial Error (mV) = 0.5, 0.8, 1.0 ;; Temp Error (ppm/oC) = 0.6, 1.0, 2.0 ;; Noise (µVpp) = 3 ;; Package = DIP14, SMT14 ;; Feature = Dual, Low Cost.

FSBB15CH60BT : Smart Power Module It is an advanced motion-smart power module (Motion-SPM) that Fairchild has newly developed and designed to provide very compact and high performance ac motor drives mainly targeting low-power inverter-driven application like air conditioner and washing machine. It combines optimized circuit protection and drive matched to low-loss.

NSI45030 : 45 V, 20 MA 15%, Constant Current Regulator & LED Driver, SOD-123 The solid state series of linear constant current regulators (CCRs) are Simple, Economical and Robust (SER) devices designed to provide a cost effective solution for regulating current in LEDs. The SER series regulators are based on patent-pending Self-Biased Transistor (SBT) technology.

OKI-78SR3.3/1.5-W36-C : Additions To Okami PoL Converter Range Feature Ultra-wide Input In Compact Package The new OKI-78SR series of switching regulator converters are ideal for industrial applications. A direct drop-in replacement for industry standard three-terminal 7803 and 7805 series LDOs, the series offers an ultra-wide input voltage range (7 to 36VDC) for nominal.

TSU6111A : USB Port SP2T Switch Supports USB & UART, TSU6111A The TSU6111A is a high performance differential autonomous SP2T switch with impedance detection. The switch supports the detection of various accessories that are attached through DP, DM, and ID. The charger detection satisfies USB charger v1.1 and VBUS_IN has a 28V tolerance to eliminate the need for external.

 
0-C     D-L     M-R     S-Z