Details, datasheet, quote on part number: LTC1147-3.3/5
PartLTC1147-3.3/5
CategoryPower Management => Supervisory Circuits => Regulator Controller
TitleRegulator Controller
DescriptionHigh Efficiency Step-down Switching Regulator Controllers
CompanyLinear Technology Corporation
DatasheetDownload LTC1147-3.3/5 datasheet
  

 

Features, Applications
LTC1147-3.3 LTC1147-5/LTC1147L High Efficiency Step-Down Switching Regulator Controllers
FEATURES

Very High Efficiency: Over 95% Possible Wide VIN Range: to 16V Current Mode Operation for Excellent Line and Load Transient Response High Efficiency Maintained Over Three Decades of Output Current Low 160µA Standby Current at Light Loads Logic Controlled Micropower Shutdown: < 20µA Short-Circuit Protection Very Low Dropout Operation: 100% Duty Cycle High Efficiency in a Small Amount of Board Space Output Can Be Externally Held High in Shutdown Available 8-Pin SO Package

The LTC®1147 series are step-down switching regulator controllers featuring automatic Burst ModeTM operation to maintain high efficiencies at low output currents. These devices drive an external P-channel power MOSFET at switching frequencies exceeding 400kHz using a constant off-time current mode architecture providing constant ripple current in the inductor. The operating current level is user-programmable via an external current sense resistor. Wide input supply range allows operation from 14V (16V maximum). Constant off-time architecture provides low dropout regulation limited by only the RDS(ON) of the external MOSFET and resistance of the inductor and current sense resistor. The LTC1147 series incorporates automatic power saving Burst Mode operation to reduce switching losses when load currents drop below the level required for continuous operation. Standby power is reduced to only 2mW at VIN = 10V (at IOUT = 0). Load currents in Burst Mode operation are typically to 300mA. For applications where even higher efficiency is required, refer to the LTC1148 data sheet and Application Note 54.

, LTC and LT are registered trademarks of Linear Technology Corporation. Burst Mode is a trademark of Linear Technology Corporation. *LTC1147L and LTC1147L-3.3 only.

Notebook and Palmtop Computers Portable Instruments Battery-Operated Digital Devices Cellular Telephones DC Power Distribution Systems GPS Systems

Operating Ambient Temperature Range to 85°C Extended Commercial Temperature Range (Note to 85°C Junction Temperature (Note 1)............................ 125°C Storage Temperature Range................ to 150°C Lead Temperature (Soldering, 10 sec)................. 300°C

Input Supply Voltage (Pin ­ 0.3V Continuous Output Current (Pin 8)...................... 50mA Sense Voltages (Pins 4, 5) VIN ­ 0.3V VIN < 12.7V............................... (VIN ­ 0.3V

TOP VIEW VIN CT 2 ITH 3 SENSE PDRIVE GND SHDN (VFB*) SENSE +
N8 PACKAGE S8 PACKAGE 8-LEAD PLASTIC DIP 8-LEAD PLASTIC SO * ADJUSTABLE OUTPUT VERSION

SYMBOL V6 I6 VOUT PARAMETER Feedback Voltage (LTC1147L) Feedback Current (LTC1147L) Regulated Output Voltage LTC1147L-3.3 LTC1147-5 Output Voltage Line Regulation Output Voltage Load Regulation LTC1147L-3.3 LTC1147-5 Burst Mode Output Ripple IQ Input DC Supply Current (Note 2) LTC1147 Series Normal Mode Sleep Mode Sleep Mode (LTC1147-5) Shutdown LTC1147L Series Normal Mode Sleep Mode Shutdown (LTC1147L-3.3)

CONDITIONS VIN = 9V VIN = 9V ILOAD = 700mA ILOAD = 700mA VIN to 12V, ILOAD 5mA < ILOAD 5mA < ILOAD < 2A ILOAD = 0A (Note 4V < VIN 4V < VIN 5V < VIN < 12V VSHDN 4V < VIN 3.5V < VIN 3.5V < VIN < 12V VSHDN 3.5V < VIN < 12V

SYMBOL V 4 PARAMETER Current Sense Threshold Voltage (Note I6 I2 tOFF , tf SHDN Pin Threshold LTC1147-3.3/LTC1147-5/LTC1147L-3.3 SHDN Pin Input Current LTC1147-3.3/LTC1147-5/LTC1147L-3.3 CT Pin Discharge Current Off-Time (Note 3) Driver Output Transition Times

CONDITIONS VSENSE­ = VOUT + 100mV (Forced) VSENSE­ = VOUT ­ 100mV (Forced) VSENSE­ = VOUT + 100mV (Forced) VSENSE­ = VOUT ­ 100mV (Forced) VSENSE­ + 25mV (Forced) VSENSE­ ­ 25mV (Forced)

0V < VSHDN < 8V, VIN = 16V VOUT in Regulation, VSENSE ­ = VOUT = 390pF, ILOAD = 3000pF (Pin 8), VIN = 6V

SYMBOL V6 VOUT PARAMETER Feedback Voltage (LTC1147L) Regulated Output Voltage LTC1147-3.3/LTC1147L-3.3 LTC1147-5 Input DC Supply Current (Note 2) LTC1147 Series Normal Mode Sleep Mode Sleep Mode (LTC1147-5) Shutdown LTC1147L Series Normal Mode Sleep Mode Shutdown (LTC1147L-3.3) Current Sense Threshold Voltage (Note LTC1147L V6 tOFF SHDN Pin Threshold LTC1147-3.3/LTC1147-5/LTC1147L-3.3 Off-Time (Note 3) CONDITIONS VIN = 9V VIN = 9V ILOAD = 700mA ILOAD = 700mA (Note 4V < VIN 4V < VIN 5V < VIN < 12V VSHDN 4V < VIN 3.5V < VIN 3.5V < VIN < 12V VSHDN 3.5V < VIN < 12V VSENSE ­ = VOUT + 100mV (Forced) VSENSE ­ = VOUT ­ 100mV (Forced) VSENSE ­ = VOUT + 100mV (Forced) VSENSE ­ = VOUT ­ 100mV (Forced) VSENSE­ + 25mV (Forced) VSENSE­ ­ 25mV (Forced) 0V < VSHDN < 8V, VIN = 390pF, ILOAD V µs

The q denotes specifications which apply over the full specified temperature range. Note TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formulas: + (PD)(150°C/W) Note 2: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See Applications Information.

Note 3: In applications where RSENSE is placed at ground potential, the offtime increases approximately 40%. Note 4: The LTC1147C is guaranteed to meet specified performance from to 70°C and is designed, characterized and expected to meet these extended temperature limits, but is not tested ­ 40°C and 85°C. The LTC1147I is guaranteed to meet the extended temperature limits. Note 5: The LTC1147L/LTC1147L-3.3 allow operation to VIN = 3.5V. Note 6: The LTC1147L is tested with external feedback resistors resulting in a nominal output voltage of 2.5V.


 

Some Part number from the same manufacture Linear Technology Corporation
LTC1147-5 High Efficiency Step-down Switching Regulator Controllers
LTC1147C
LTC1147C-3.3
LTC1147HVCS8-3.3
LTC1147I
LTC1147I-3.3
LTC1148 High Efficiency Synchronous Step-down Switching Regulators
LTC1148-3.3/5
LTC1148-5
LTC1149 LTC1149, 48V Synchronous Step-down
LTC1150 LTC1150, 15V Zero-drift Operational Amplifier With Internal Capacitors
LTC1151 LTC1151, Dual 15V Zero-drift Operational Amplifier
LTC1151CSW Dual 15V Zero-drift Operational Amplifier
LTC1152 LTC1152, Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1152C Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1152CN8 LTC1152, Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1152I Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1152IN8 LTC1152, Rail-to-rail Input Rail-to-rail Output Zero-drift op Amp
LTC1153 LTC1153, Auto-reset Electronic Circuit Breaker
LTC1153IN8 Auto-reset Electronic Circuit Breaker
LTC1154 LTC1154, High-side Micropower MOSFET Driver

LTC1062CSW : LTC1062, 5th Order, 20kHz, Butterworth, DC Accurate, Low Pass Filter

LTC1418AC : ->Single Input LTC1418 5V or +/-5V, 200ksps, 15mW With Serial/parallel I/o

LTC1741CFW : ->Single Input LTC1741, 5V, 12-Bit, 65Msps Low Noise ADC, Parallel Interface

LT3519EMSTRPBF : LED Driver with Integrated Schottky Diode

LTC4000IUFD#PBF : High Voltage High Current Controller For Battery Charging And Power Management The LTC®4000 is a high voltage, high performance controller that converts many externally compensated DC/DC power supplies into full-featured battery chargers. Features of the LTC4000’s battery charger include: acc

LTC1065CSW#TR : Interface - Filter - Active Integrated Circuit (ics) Bessel, Lowpass Switched Capacitor Tape & Reel (TR) ±2.37 V ~ 8 V; IC FILTER LP 5TH ORD LIN 16SOIC Specifications: Package / Case: 16-SOIC (0.295", 7.50mm Width) ; Filter Type: Bessel, Lowpass Switched Capacitor ; Voltage - Supply: ±2.37 V ~ 8 V ; Number of Filters: 1 ; Filter Order: 5th ; Frequency - Cutoff or Center: 50kHz ; Packaging: Tape & Reel (TR) ; Lead Free Status: Contains Lead ; Ro

LTC1484CMS8#PBF : LTC1484, Low Power RS485 Transceiver With Receiver Fail-Safe, MS-8

LT3497EDDB#TRPBF : LED DISPLAY DRIVER, PDSO10 Specifications: Device Type: LED Driver ; Supply Voltage: 3V ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: 3 X 2 MM, LEAD FREE, PLASTIC, MO-229WECD-1, DFN-10 ; Pins: 10 ; Features: RoHS

LTC2636IMS-L8#TRPBF : 10-BIT DAC, PDSO14 Specifications: Package Type: 4 X 3 MM, LEAD FREE, PLASTIC, MO-229WGED-3, DFN-14 ; Pins: 14

SSTPAD100T1 : 0.01 A, SILICON, SIGNAL DIODE Specifications: Package: ROHS COMPLIANT, PLASTIC PACKAGE-3 ; Number of Diodes: 1 ; IF: 10 mA ; RoHS Compliant: RoHS

Same catergory

CD4016BMS : Radiation Hardened CMOS Quad Bilateral Switch. Applications Analog Signal Switching/Multiplexing Signal Gating Squelch Control Chopper Modulator Demodulator Commutating Switch Digital Signal Switching/Multiplexing CMOS Logic Implementation Analog to Digital & Digital to Analog Conversion Digital Control of Frequency, Impedance, Phase, and Analog Signal Gain Transmission or Multiplexing of Analog.

EZ1581CM : Dual Input Low Dropout Regulator. The EZ158X family of high performance positive voltage regulators are designed for use in applications requiring very low dropout voltage 5, 3 and 1.5 amps. When supplying 2.5V on motherboards where both 5V and 3.3V supplies are available, the superior dropout characteristics of the EZ158X result in reduced heat dissipation compared to regular LDOs,.

LM4140 : LM4140 - Precision Micropower Low Dropout Voltage Reference, Package: Soic Narrow, Pin Nb=8.

P3BU-0505E : Power/w = 0,5 ;; Input/vdc = 5/12/24 ;; Output/vdc = 3,3/5/7,2/12/15/18 ;; ISOlation = 1000V ;; Package = DIP8.

PT78NR105 : Non-Isolated DC-DC Converters. 1 Amp Plus to Minus Voltage Integrated Switching Regulator Negative output from positive input Wide Input Range Self-Contained Inductor Short Circuit Protection Over-T emperature Protection Fast Transient Response The PT78NR100 Series creates a negative output voltage from a positive input voltage greater than 7V. These easy-to-use, 3-terminal, Integrated.

S-8424A : voltage detectors+voltage regulators. Feature = Battery Backup Switching ic ;; Composition = 2V/R + 3V/D + SW ;; Output Current = - ;; Output Voltage = 2.3-5.4 V (0.1V Step) ;; Detection Voltage = 2.4-5.3 V(CS), 1.7-3.4 V(PREEND, RESET) ;; Accuracy = ±2% ;; Current Consumption = 15 µA Max. (Operating) 2.1 µA Max. (Back Up) ;; Package.

TLE2426 : The Rail Splitter Precision Virtual Ground. 1/2 VI Virtual Ground for Analog Systems Self-Contained 3-terminal TO-226AA Package Micropower Operation. 170 µA Typ, 5 V Wide VI Range. 40 V High Output-Current Capability ­ Source. 20 mA Typ ­ Sink. 20 mA Typ Excellent Output Regulation 45 µV Typ +15 µV Typ 10 mA Low-Impedance Output. 0.0075 Typ Noise Reduction Pin (D, JG, and P Packages Only) In signal-conditioning.

TPS2102D : Power MUXes. ti TPS2102, 2.7-4V Dual In/single Out MOSFET, 0.5A Main/0.1A Aux Input, Act-low Enable, Comm. Temp..

TPS76525D : ti TPS76525, Ultra-low-quiescent-current 150-mA LDO Linear Regulators.

ADT7476 : dBCool™ Remote Thermal Controller and Voltage Monitor The ADT7476 dBCOOL™ controller is a thermal monitor and multiple PWM fan controller for noise-sensitive or powersensitive applications requiring active system cooling. The ADT7476 can drive a fan using either a low or high frequency drive signal, monitor the temperature of up to two remote sensor.

IL3843 : Current Mode PWM Controller PKG : DIP-8 3. Pin to Pin compatible : UC3843A (ST semiconductor , TI ) 4. Feature • Automatic Feed Forward Compensation • High Gain Totem Pole Output • Internally Trimmed Bandgap Reference • Undervoltage Lockout with Hysteresis • Low Start Up Current • Current mode operation to 500KHz 5. Application • SMPS , Adaptor.

BQ25017 : The bq25015/7 are highly integrated charge and power management devices targeted at space-limited bluetooth applications. The bq25015/7 devices offer integrated power FET and current sensor for charge control, reverse blocking protection, high accuracy current and voltage regulation, charge status, charge termination, and a highly efficient and low-power.

TPS5450 : 5A, Wide Input Step Down SWIFT Converter As a member of the SWIFT™ family of DC/DC regulators, the TPS5450 is a high-output-current PWM converter that integrates a low resistance high side N-channel MOSFET. Included on the substrate with the listed are a high performance voltage error amplifier that provides tight voltage regulation accuracy under transient.

NCP5215 : Dual Synchronous Buck Controller for Notebook The NCP5215, a high-efficiency and fast-transient-response dual-channel buck controller, provides a multifunctional power solution for notebook power system. 180o interleaved operation function between the two channels has capabilities of reducing the common input capacitor requirement and improving noise.

LTC4090 : USB Power Manager With 2A High Voltage Bat-Track Buck Regulator The LTC4090/LTC4090-5 are USB power managers plus high voltage Li-Ion/Polymer battery chargers. The devices control the total current used by the USB peripheral for operation and battery charging. Battery charge current is automatically reduced such that the sum of the load current and the charge.

XC9101 : PWM Controlled Step-Up DC/DC Controller The XC9101 series are step-up multiple current and voltage feedback DC/DC controller ICs. Current sense, clock frequencies and amp feedback gain can all be externally regulated. A stable power supply is possible with output currents of up to 1.5A. With output voltage fixed internally, VOUT is selectable in 0.1V.

 
0-C     D-L     M-R     S-Z