Details, datasheet, quote on part number: ISL43L710IU-T
PartISL43L710IU-T
CategoryAnalog & Mixed-Signal Processing => Switches & Multiplexers => Analog Switches
DescriptionUltra Low ON-Resistance, Single Supply, Differential SPST Analog Switches<<<>>>the Intersil ISL43L710, ISL43L711, ISL43L712 Devices Are Low ON-resistance, Low Voltage, Bidirectional, Precision, Differential Single-pole/single-throw (SPST) Analog Switches Designed to Operate From a Single +1.65V to +3.6V Supply. Targeted Applications Include Battery Powered Equipment That Benefit From Low Ron (0.16 ), Low Power Consumption (0.12W) And Fast Switching Speeds (tON = 13ns, Toff = 13ns).<<<>>><<<>>>Cell Phones, For Example, Often Face Asic Functionality Limitations. The Number of Analog Input or Gpio Pins May be Limited And Digital Geometries Are Not Well Suited to Analog Switch Performance. This Family of Parts May be Used to Switch in Additional Functionality While Reducing Asic Design Risk. The ISL43L71X Are Offered in Small Form Factor Packages, Alleviating Board Space Limitations.<<<>>><<<>>>the ISL43L710, ISL43L711, ISL43L712 Are Differential Single-pole/single-throw (SPST) Devices. The ISL43L710 Has Two Normally Open (NO) Switches; The ISL43L711 Has Two Normally Closed (NC) Switches; The ISL43L712 Has One Normally Open (NO) And One Normally Closed (NC) Switch And CAN be Used as an Spdt. The ISL43L712 is Equipped With an Inhibit Pin to Simultaneously Open All Signal Paths.<<<>>> <<<>>> <<<>>>Key Features <<<>>> <<<>>> <<<>>>Pb-Free Available as an Option (see Ordering Info) <<<>>>Low on Resistance (RON) <<<>>>V+ = 3.0V 0.16 <<<>>>V+ = 1.8V 0.26 <<<>>>RON Matching Between Channels 0.005 <<<>>>RON Flatness Over Signal Range 0.008 <<<>>>Single Supply Operation +1.65V to +3.6V <<<>>>Low Power Consumption (PD) <0.12W <<<>>>Fast Switching Action (V+ = 3.0V) <<<>>>tON 13ns <<<>>>tOFF 13ns <<<>>>ESD HBM Rating >8kV <<<>>>1.8V Logic Compatible (+3V Supply) <<<>>>Available in 8-Ld Thin DFN And 8-Ld Msop Packages
CompanyIntersil Corporation
DatasheetDownload ISL43L710IU-T datasheet
Cross ref.Similar parts: TXS0102YZPR
Quote
Find where to buy
 
PackagesInd 8 Ld MSOP T+R
  

 

Features, Applications

Ultra Low ON-Resistance, Single Supply, Differential SPST Analog Switches

The Intersil ISL43L711, ISL43L712 devices are low ON-resistance, low voltage, bidirectional, precision, differential single-pole/single-throw (SPST) analog switches designed to operate from a single to +3.6V supply. Targeted applications include battery powered equipment that benefit from low RON (0.16), low power consumption (0.12W) and fast switching speeds (tON = 13ns, tOFF = 13ns). Cell phones, for example, often face ASIC functionality limitations. The number of analog input or GPIO pins may be limited and digital geometries are not well suited to analog switch performance. This family of parts may be used to switch in additional functionality while reducing ASIC design risk. The ISL43L71X are offered in small form factor packages, alleviating board space limitations. The ISL43L711, ISL43L712 are differential single-pole/single-throw (SPST) devices. The ISL43L710 has two normally open (NO) switches; the ISL43L711 has two normally closed (NC) switches; the ISL43L712 has one normally open (NO) and one normally closed (NC) switch and can be used as an SPDT. The ISL43L712 is equipped with an inhibit pin to simultaneously open all signal paths. Table 1 summarizes the performance of this family.

TABLE 1. FEATURES AT A GLANCE ISL43L710 NUMBER OF SWITCHES 2 1.8V RON 1.8V tON/tOFF 3V RON 3V tON/tOFF PACKAGES 2 NO/NO ISL43L711 2 NC/NC ISL43L712 2 NO/NC 0.16 13ns/13ns

Features

Pb-Free Available as an Option (see Ordering info) Low ON Resistance (RON) 1.8V. 0.26 RON Matching Between Channels. 0.005 RON Flatness Over Signal Range. 0.008 Single Supply Operation. to +3.6V Low Power Consumption (PD). <0.12W Fast Switching Action (V+ 3.0V) - tON. 13ns - tOFF. 13ns ESD HBM Rating. >8kV 1.8V Logic Compatible (+3V Supply) Available in 8-Ld thin DFN and 8-Ld MSOP Packages

Applications

Battery Powered, Handheld, and Portable Equipment - Cellular/Mobile Phones - Pagers - Laptops, Notebooks, Palmtops Portable Test and Measurement Medical Equipment Audio and Video Switching

Technical Brief TB363 "Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)". Application Note AN557 "Recommended Test Procedures for Analog Switches".

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2004. All Rights Reserved All other trademarks mentioned are the property of their respective owners.

(Note 2) PART NO. (BRAND) * (L710) (Note * (L70) (See Note * (L711) (Note * (L71) (Note 3) TEMP. RANGE (C) to 85 PACKAGE 8 Ld MSOP PKG. DWG. # M8.118

(Note 2) PART NO. (BRAND) * (L712) (Note * (L72) (Note 3) NOTES: 2. Most surface mount devices are available on tape and reel; add "-T" to suffix. 3. Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-Free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC Std-020B. * Pb-free Parts Coming Soon. TEMP. RANGE (C) to 85 PACKAGE 8 Ld MSOP (Pb-free) PKG. DWG. # M8.118

PIN V+ GND FUNCTION System Power Supply Input to +3.6V) Ground Connection Digital Control Input Analog Switch Common Pin Analog Switch Normally Open Pin Analog Switch Normally Closed Pin Digital Control Input. Connect to GND for Normal Operation. Connect V+ to turn all switches off. No Connect

V+ to GND. to 4.7V Input Voltages IN (Note -0.3 to ((V+) + 0.3V) NO, NC (Note -0.3 to ((V+) + 0.3V) Output Voltages COM (Note -0.3 to ((V+) + 0.3V) Continuous Current (Any Terminal). 300mA Peak Current, IN, NO, NC, or COM (Pulsed 1ms, 10% Duty Cycle, Max). 500mA ESD Rating (Per MIL-STD-883 Method 3015).>8kV

Thermal Resistance (Typical, Note 5) JA (C/W) Ld 3x3 thin DFN Package. 8 Ld MSOP Package. 190 Maximum Junction Temperature (Plastic Package). 150C Maximum Storage Temperature Range. to 150C Maximum Lead Temperature (Soldering 10s). 300C (Lead Tips Only)

CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES: 4. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings. JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

Test Conditions: to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Notes 6, 8), Unless Otherwise Specified TEST CONDITIONS TEMP (C) MIN (NOTE 7) TYP MAX (NOTE 7) UNITS

PARAMETER ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG ON Resistance, RON

Full = 2.7V, ICOM = 100mA, VNO or VNC to V+ (See Figure = 2.7V, ICOM = 100mA, VNO or VNC = Voltage at Max RON, (Note = 2.7V, ICOM = 100mA, VNO or VNC 0V to V+, (Note = 3.3V, VCOM 0.3, 3V, VNO or VNC 0.3V 25 Full 25 Full 25 Full 25 Full = 3.3V, VCOM 3V, or VNO or VNC 3V 25 Full

or NC OFF Leakage Current, INO(OFF) or INC(OFF) COM ON Leakage Current, ICOM(ON) DYNAMIC CHARACTERISTICS Turn-ON Time, tON

= 2.7V, VNO or VNC = 35pF, VIN to 2.7V, (See Figure 1, Note = 2.7V, VNO or VNC = 35pF, VIN to 2.7V, (See Figure 1, Note = 0, (See Figure = 100kHz, VCOM = 1 VRMS, (See Figure = 100kHz, VCOM = 1 VRMS, (See Figure 5)


 

Related products with the same datasheet
ISL43L710IR
ISL43L710IR-T
ISL43L710IU
ISL43L711
ISL43L711IR
ISL43L711IR-T
ISL43L711IU
ISL43L711IU-T
ISL43L712
ISL43L712IR
ISL43L712IR-T
Some Part number from the same manufacture Intersil Corporation
ISL43L711 Ultra Low ON-Resistance, Single Supply, Differential SPST Analog Switches<<<>>>the Intersil ISL43L710, ISL43L711, ISL43L712 Devices Are Low ON-resistance, Low Voltage, Bidirectional, Precision, Differential
ISL4485E RS-485/RS-422 Transceivers, 20Mbps, Esd Protected to 15kV, Half Duplex, 5V, With Rx/tx Enables <<<>>> <<<>>>The Intersil ISL4485E is a High Speed, Bicmos 5V Powered, Single Transceiver That Meets Both
ISL4486 5V, Ultra High Speed, Profibus, RS-485/RS-422 Transceivers <<<>>> <<<>>>The Intersil ISL4486 And ISL81486 Are Bicmos, 5V Powered, Single Transceivers That Meet Both The RS-485 And RS-422 Standards For Balanced
ISL4489E 15kV Esd Protected, 1/8 Unit Load, 5V, Low Power, Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers <<<>>> <<<>>>The ISL4489E, ISL4491E Are Esd Protected, Fractional Unit Load, Bicmos, 5V Powered,
ISL4489E
ISL4489EIB
ISL4489EIB
ISL4489EIB-T
ISL4489EIB-T
ISL4491E 15kV Esd Protected, 1/8 Unit Load, 5V, Low Power, High Speed, Full Duplex, RS-485/RS-422 Transceivers <<<>>> <<<>>>The ISL4489E, ISL4491E Are Esd Protected, Fractional Unit Load, Bicmos, 5V Powered, Single
ISL4491E 15kV Esd Protected, 1/8 Unit Load, 5V, Low Power, Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers <<<>>>The ISL4489E, ISL4491E Are Esd Protected, Fractional Unit Load, Bicmos, 5V Powered, Single
ISL4491EIB 15kV Esd Protected, 1/8 Unit Load, 5V, Low Power, High Speed, Full Duplex, RS-485/RS-422 Transceivers <<<>>> <<<>>>The ISL4489E, ISL4491E Are Esd Protected, Fractional Unit Load, Bicmos, 5V Powered, Single
ISL4491EIB 15kV Esd Protected, 1/8 Unit Load, 5V, Low Power, Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers <<<>>>The ISL4489E, ISL4491E Are Esd Protected, Fractional Unit Load, Bicmos, 5V Powered, Single
ISL4491EIB-T 15kV Esd Protected, 1/8 Unit Load, 5V, Low Power, High Speed, Full Duplex, RS-485/RS-422 Transceivers <<<>>> <<<>>>The ISL4489E, ISL4491E Are Esd Protected, Fractional Unit Load, Bicmos, 5V Powered, Single
ISL4491EIB-T 15kV Esd Protected, 1/8 Unit Load, 5V, Low Power, Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers <<<>>>The ISL4489E, ISL4491E Are Esd Protected, Fractional Unit Load, Bicmos, 5V Powered, Single
ISL5120 Low-Voltage, Single Supply, Dual Spst, SPDT Analog Switches
ISL5120CU Low-voltage, Single Supply, Dual Spst, SPDT Analog Switches
ISL5120IB Low-Voltage, Single Supply, Dual Spst, SPDT Analog Switches
ISL5216 ISL5216 Datasheet
ISL5217 Quad Programmable up Converter
ISL5239 Pre-distortion Linearizer

HS1-1825ARH : Radiation Hardened High-speed, Dual Output PWM

ICL3243CB-T : 1 Microamp Supply-Current, +3V to +5.5V, 250kbps, RS-232 Transmitters/receivers

IRFF220 : 3.5a, 200v, 0.800 Ohms, N-channel Power MOSFET: 200v, 3.5a

RF1K49090 : 3.5A, 12V, 0.050 Ohm, Logic Level, Dual N-channel LittleFET

ISL22414WFU10Z : Single Digitally Controlled Potentiometer (XDCP), Low Noise, Low Power, I2C Bus, 256 Taps The ISL22414 integrates a single digitally controlled potentiometer (DCP), control logic and non-volatile memory on a monolithic CMOS integrated circuit.

HFA1105EVAL : 330mhz, Low Power, Current Feedback Video Operational Amplifier

MR82C37A-5/B : CMOS High Performance Programmable DMA Controller

HIP6004BCR-T : Pmic - Voltage Regulator - Special Purpose Integrated Circuit (ics) Tape & Reel (TR); IC CTRLR PWM VOLTAGE MON 20-QFN Specifications: Package / Case: 20-VQFN Exposed Pad ; Packaging: Tape & Reel (TR) ; Lead Free Status: Contains Lead ; RoHS Status: RoHS Non-Compliant

X1227S8-4.5A : Clock/timing - Real Time Clock Integrated Circuit (ics) Clock/Calendar Tube 4.5 V ~ 5.5 V; IC RTC CPU SUP WDT 4K EE 8-SOIC Specifications: Date Format: YY-MM-DD-dd ; Time Format: HH MM SS (12/24 hr) ; Voltage - Supply: 4.5 V ~ 5.5 V ; Interface: I&sup2;C ; Memory Size: - ; Package / Case: 8-SOIC (0.154", 3.90mm Width) ; Packaging: Tube ; Type: Clock/Calendar ; Operating Temperature: 0C ~ 70C ; Lead Free Status: Co

EL5176IYZ-T13 : LINE DRIVER Specifications: Device Type: Line / Bus Driver

 
0-C     D-L     M-R     S-Z