Details, datasheet, quote on part number: ISL4241E
PartISL4241E
CategoryAnalog & Mixed-Signal Processing
DescriptionQFN Packaged, +/-15kV Esd Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps, RS-232 Transmitters/receivers
CompanyIntersil Corporation
DatasheetDownload ISL4241E datasheet
Quote
Find where to buy
 
  

 

Features, Applications

The Intersil ISL424XE devices are to 5.5V powered RS-232 transmitters/receivers which meet ElA/TIA-232 and V.28/V.24 specifications, even at VCC = 3.0V. Additionally, they provide 15kV ESD protection (IEC61000-4-2 Air Gap and Human Body Model) on transmitter outputs and receiver inputs (RS-232 pins). Targeted applications are PDAs, Palmtops, and notebook and laptop computers where the low operational, and even lower standby, power consumption is critical. Efficient on-chip charge pumps, coupled with manual and automatic powerdown functions, reduce the standby supply current a 10nA trickle. Tiny x 5mm Quad Flat No-Lead (QFN) packaging and the use of small, low value capacitors ensure board space savings as well. Data rates greater than 250kbps are guaranteed at worst case load conditions. The ISL424XE are 3 driver, 5 receiver devices that, coupled with the 5x5 QFN package, provide the industry's smallest, lowest power complete serial port suitable for PDAs, and laptop or notebook computers. The 5x5 QFN requires 60% less board area than a 28 lead TSSOP, and is nearly 20% thinner. The devices also include a noninverting alwaysactive receiver for "wake-up" capability. The ISL4243E features an automatic powerdown function that powers down the on-chip power-supply and driver circuits. This occurs when an attached peripheral device is shut off or the RS-232 cable is removed, conserving system power automatically without changes to the hardware or operating system. It powers up again when a valid RS-232 voltage is applied to any receiver input. Table 1 summarizes the features of the ISL424XE, while Application Note AN9863 summarizes the features of each device comprising the 3V RS-232 family.

Features

Parameters Fully Specified for 10% Tolerance Supplies and Full Industrial Temp Range Available in Small QFN x 5mm) Package which is 60% Smaller than a 28 Lead TSSOP ESD Protection for RS-232 I/O Pins 15kV (IEC61000) Meets EIA/TIA-232 and V.28/V.24 Specifications 3V RS-232 Compatible with VCC = 2.7V On-Chip Voltage Converters Require Only Four External 0.1F Capacitors Manual and Automatic Powerdown Features Receiver Hysteresis For Improved Noise Immunity Guaranteed Minimum Data Rate. 250kbps Wide Power Supply Range. Single to +5.5V Low Supply Current in Powerdown State.10nA

Applications

Any Space Constrained System Requiring RS-232 Ports - Battery Powered, Hand-Held, and Portable Equipment - Laptop Computers, Notebooks - PDAs and Palmtops, Data Cables - Cellular/Mobile Phones, Digital Cameras, GPS Receivers

Technical Brief TB363 "Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices "Technical Brief TB379 "Thermal Characterization of Packages for ICs" Technical Brief TB389 "PCB Land Pattern Design and Surface Mount Guidelines for QFN Packages"

TABLE 1. SUMMARY OF FEATURES PART NUMBER ISL4241E ISL4243E NO. OF MONITOR Rx. NO. OF NO. OF QFN PKG. (ROUTB) Tx. Rx. AVAILABLE? YES 2 1 DATA RATE (kbps) 250 Rx. ENABLE FUNCTION? YES NO READY OUTPUT? NO MANUAL POWERDOWN? YES AUTOMATIC POWERDOWN FUNCTION? NO YES

PART NO. ISL4243EIR ISL4243EIR-T TEMP. RANGE (oC) to 85 PACKAGE 32 Ld QFN Tape & Reel 32 Ld QFN Tape & Reel PKG. NO. L32.5x5

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2003. All Rights Reserved All other trademarks mentioned are the property of their respective owners.

PIN VCC V+ VGND C1C2+ C2TIN TOUT RIN ROUT ROUTB INVALID System power supply input to 5.5V). Internally generated positive transmitter supply (+5.5V). Internally generated negative transmitter supply (-5.5V). Ground connection. External capacitor (voltage doubler) is connected to this lead. External capacitor (voltage doubler) is connected to this lead. External capacitor (voltage inverter) is connected to this lead. External capacitor (voltage inverter) is connected to this lead. TTL/CMOS compatible transmitter Inputs. 15kV ESD Protected, RS-232 level (nominally 5.5V) transmitter outputs. 15kV ESD Protected, RS-232 compatible receiver inputs. TTL/CMOS level receiver outputs. TTL/CMOS level, noninverting, always enabled receiver outputs. Active low output that indicates if no valid RS-232 levels are present on any receiver input. FUNCTION

FORCEOFF Active low to shut down transmitters and on-chip power supply. This overrides any automatic circuitry and FORCEON (see Table 2). FORCEON EN SHDN NC Active high input to override automatic powerdown circuitry thereby keeping transmitters active. (FORCEOFF must be high). Active low receiver enable control. Active low input to shut down transmitters and on-board power supply, to place device in low power mode. No Connection

0.1F 26 VCC T3OUT RS-232 LEVELS R2OUTB 18 TTL/CMOS LOGIC LEVELS 22 21 SHDN GND 24 VCC TO POWER CONTROL LOGIC 21 FORCEOFF 20 INVALID GND 22 R5 FORCEON R3IN RS-232 LEVELS 1 R1IN TTL/CMOS LOGIC LEVELS R3IN RS-232 LEVELS 23 +


 

Related products with the same datasheet
ISL4241EIR
ISL4241EIR-T
ISL4243E
ISL4243EIR
ISL4243EIR-T
Some Part number from the same manufacture Intersil Corporation
ISL4241EIR QFN Packaged, +/-15kV Esd Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps, RS-232 Transmitters/receivers
ISL4244E QFN Packaged, 15kV Esd Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps/ 1Mbps, RS-232 Transceivers With Enhanced Automatic Powerdown
ISL4260E QFN Packaged, 15kV Esd Protected, +3V to +5.5V, 150nA, 250kbps, RS-232 Transmitters/receivers With Separate Logic Supply
ISL4270E QFN Packaged, +/-15kV Esd Protected, +3V to +5.5V, 300nA, 250kbps, RS-232 Transceivers With Enhanced Automatic Powerdown And a Separate Logic Supply
ISL43110 Low-Voltage, Single Supply, Spst, High Performance Analog Switches
ISL43112 Low-Voltage, Dual Supply, Spst, High Performance Analog Switches
ISL43120 Low-Voltage, Single Supply, Dual Spst, SPDT Analog Switches
ISL43140 Low-Voltage, Single And Dual Supply, High Performance, Quad Spst, Analog Switches
ISL43143 Low-Voltage, Single And Dual Supply, Quad Spst, High Performance Analog Switches
ISL43210 Low-Voltage, Single Supply, Dual Spst, SPDT Analog Switches
ISL43231 Low-voltage, Single And Dual Supply, Triple SPDT Analog Switch
ISL43240 Low-Voltage, Single And Dual Supply, Quad Spdt, Analog Switches
ISL43410 Low-Voltage, Single Supply, DPDT High Performance Analog Switch
ISL43485 3.3V, Low Power, 30Mbps, RS-485/RS-422 Transceiver
ISL43640 Low-Voltage, Single Supply, 4 to 1 Multiplexer, High Performance Analog Switch
ISL43681 Low-voltage, Single And Dual Supply, 8 to 1 Multiplexer And Differential 4 to 1 Multiplexer
ISL43741
ISL43840 Low-voltage, Single And Dual Supply, Dual 4 to 1 Multiplexer Analog Switch With Enable

ICL7641 : Dual/Quad, Low Power CMOS Operational Amplifiers

ISL43410IU : Low-Voltage, Single Supply, DPDT High Performance Analog Switch

MD82C37A-5B : CMOS High Performance Programmable Dma Controller

ISL90460UIE527-TK : Single Volatile 32-Tap Digitally Controlled Potentiometer (XDCP) The Intersil ISL90460 is a digitally controlled potentiometer (XDCP). Configured as a variable resistor, the device consists of a resistor array, wiper switches, a control section, and volatile memory. The wiper position is controlle

ISL21009BFB841Z : 100v, 2A Peak, High Frequency Half-bridge Drivers

HI1396_00 : 8-bit, 125 Msps, Flash A/D Converter

HI1176-EV : 8-bit, 20 Msps, Flash A/D Converter

ISL55009 : MMIC Silicon Bipolar Broadband Amplifier

ISL6614IR-T : Dual Advanced Synchronous Rectified Buck Mosfet Drivers with Protection Features

ISL9000IRFDZ-T : DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO10 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, 3 X 3 MM, PLASTIC, MO-229WEED-3, DFN-10 ; Life Cycle Stage: ACTIVE ; Output Voltage: 3.3 volts ; IOUT: 0.1000 amps ; VIN: 2.3 to 5.5 volts

Same catergory

AD8001 : 800 Mhz, 50 MW Current Feedback Amplifier. Excellent Video s (RL = +2) Gain Flatness to 100 MHz 0.01% Differential Gain Error 0.025 Differential Phase Error Low Power 5.5 mA Max Power Supply Current (55 mW) High Speed and Fast Settling 880 MHz, 3 dB Bandwidth +1) 440 MHz, 3 dB Bandwidth V/ s Slew Rate 10 ns Settling Time to 0.1% Low Distortion 65 dBc THD, MHz 33 dBm 3rd Order Intercept, = 10 MHz 66 dB SFDR,.

CMV1036YR : Micropower Pro Operational Amplifier With Shutdown.

DS2434 : Power. Battery Identification Chip.

FX806A : Audio Processor. CHIP SELECT POWER SUPPLY C-BUS INTERFACE CALIBRATION INPUT PRIMARY and SECONDARY AUDIO INPUTS Voice. Sub-/Audio Tone. FFSK. etc. SERIAL CLOCK COMMAND DATA MAIN PROCESS OUT SUM OUT MOD. IN (TX) MIC. IN MIC. & VOGAD AMPS LOW & HIGHPASS FILTERS Intended primarily to operate as the "Audio Terminal" of Radio Systems using the DBS 800 Digitally-integrated.

LM293AM : Dual Differential Comparator. Single Supply Operation: to 36V Dual Supply Operation: to 18V Allow Comparison of Voltages Near Ground Potential Low Current Drain 800A Typ. Compatible with all Forms of Logic Low Input Bias Current 25nA Typ. Low Input Offset Current 5nA Typ. Low Offset Voltage 1mV Typ. The LM293/ LM293A consist of two independent voltage comparators designed to operate.

MAX312 : 10, Quad, Spst, CMOS Analog Switches. Maxim's MAX312/MAX313/MAX314 analog switches feature low on-resistance (10 max) and 1.5 on-resistance matching between channels. These switches conduct equally well in either direction. They offer low leakage over temperature at +85C). Low power consumption and ESD tolerance greater than 2000V per Method 3015.7 are guaranteed. The MAX312/MAX313/MAX314.

MAX909C/D : Single/dual/quad High-speed, Ultra Low-power, Single-supply TTL Comparators.

MC33171D : Low Power 3-44V Single Channel Operational Amplifier, Package: Soic, Pins=8.

NJM4565 : Dual Operational Amplifier.

OPA1013CN8 : ti OPA1013, Precision, Single-supply Dual Operational Amplifier. SINGLE POWER SUPPLY OPERATION INPUT VOLTAGE RANGE TO GROUND OUTPUT SWINGS NEAR GROUND LOW QUIESCENT CURRENT: 550A max LOW VOS: 300V max APPLICATIONS PRECISION INSTRUMENTATION BATTERY-POWERED EQUIPMENT BRIDGE AMPLIFIERS 4-20mA CURRENT TRANSMITTERS VOLTAGE COMPARATOR The OPA1013 dual operational amplifier provides precision performance in single power.

OPA348 : . LOW IQ: 45A typical LOW COST RAIL-TO-RAIL INPUT AND OUTPUT SINGLE SUPPLY: to +5.5V INPUT BIAS CURRENT: 0.5pA MicroSIZE PACKAGES: SC70-5, SOT23-8 and TSSOP-14 q HIGH SPEED:POWER WITH BANDWIDTH: 1MHz The OPA348 series amplifiers are single supply, low-power, CMOS op amps in micro packaging. Featuring an extended bandwidth of 1MHz, and a supply current.

THS4082 : Dual. 175-mhz Low-power High-speed Amplifiers. Ultralow 3.4 mA Per Channel Quiescent Current High Speed 175 MHz Bandwidth (3 dB, G V/s Slew Rate 43 ns Settling Time (0.1%) High Output Drive, 85 mA (typ) Excellent Video Performance 35 MHz Bandwidth (0.1 dB, G Differential Gain 0.05 Differential Phase Very Low Distortion THD = 64 dBc = 1 MHz, RL THD = 79 dBc = 1 MHz, 1 k) Wide Range of Power.

X9258 : Quad 256 Tap Xdcp, Low Power, Two-wire Interface, Dual Supply. Four potentiometers in one package 256 resistor taps/pot0.4% resolution 2-wire serial interface Wiper resistance, 40 typical = -5V Four nonvolatile data registers for each pot Nonvolatile storage of wiper position Standby current < 5A max (total package) Power supplies --VCC to 5.5V --V+ to 5.5V --V- 100K, 50K total pot resistance High reliability.

NJM8532 : Rail-to-Rail Input/Output Dual Operational Amplifier The NJM8532 is a Rail-to-Rail Input/Output dual operational amplifier featuring Low power, low noise and operation from 1.8V. NJM8532RB1 Rail-to-Rail Input/Output provides wide dynamic range, is from ground to power supply level. In addition to ground sensing applications, NJM8532 enable to be applied.

LTC6247 : 180MHz, 1mA Power Efficient Dual Rail-to-Rail I/O Op Amps The LTC6246/LTC6247/LTC6248 are single/dual/quad low power, high speed unity gain stable rail-to-rail input/output operational amplifiers. On only 1mA of supply current they feature an impressive 180MHz gain-bandwidth product, 90V/?s slew rate and a low 4.2nV/?Hz of input-referred noise. The combination.

 
0-C     D-L     M-R     S-Z