Details, datasheet, quote on part number: CA3160AT3
CategoryAnalog & Mixed-Signal Processing => Amplifiers => Operational Amplifiers
CompanyIntersil Corporation
DatasheetDownload CA3160AT3 datasheet
Find where to buy


Features, Applications

4MHz, BiMOS Operational Amplifier with MOSFET Input/CMOS Output

The CA3160A and CA3160 are integrated circuit operational amplifiers that combine the advantage of both CMOS and bipolar transistors on a monolithic chip. The CA3160 series are frequency compensated versions of the popular CA3130 series. Gate protected P-Channel MOSFET (PMOS) transistors are used in the input circuit to provide very high input impedance, very low input current, and exceptional speed performance. The use of PMOS field effect transistors in the input stage results in common-mode input voltage capability down to 0.5V below the negative supply terminal, an important attribute in single supply applications. A complementary symmetry MOS (CMOS) transistor-pair, capable of swinging the output voltage to within 10mV of either supply voltage terminal (at very high values of load impedance), is employed as the output circuit. The CA3160 Series circuits operate at supply voltages ranging from to 8V when using split supplies, and have terminals for adjustment of offset voltage for applications requiring offset null capability. Terminal provisions are also made to permit strobing of the output stage. The CA3160A offers superior input characteristics over those of the CA3160.


MOSFET Input Stage Provides: - Very High x 1012) (Typ) - Very Low II. 5pA (Typ) at 15V Operation. 2pA (Typ) at 5V Operation Common-Mode Input Voltage Range Includes Negative Supply Rail; Input Terminals Can Be Swung 0.5V Below Negative Supply Rail CMOS Output Stage Permits Signal Swing to Either (or Both) Supply Rails


Ground Referenced Single Supply Amplifiers Fast Sample Hold Amplifiers Long Duration Timers/Monostables High Input Impedance Wideband Amplifiers Voltage Followers (e.g., Follower for Single Supply D/A Converter) Wien-Bridge Oscillators Voltage Controlled Oscillators Photo Diode Sensor Amplifiers


NOTE: CA3160 Series devices have an on-chip frequency compensation network. Supplementary phase compensation or frequency roll-off (if desired) can be connected externally between Terminals 1 and 8.

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2002. All Rights Reserved

Absolute Maximum Ratings Supply Voltage (Between V+ and V- Terminals).+16V Differential Mode Input Voltage.8V Input Voltage. (V+ +8V) to (V- -0.5V) Input Current. 1mA Output Short Circuit Duration (Note 2). Indefinite Operating Conditions Temperature Range. to 125oC

CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

Thermal Resistance (Typical, Note 1) JA (oC/W) JC (oC/W) PDIP Package. 115 N/A Maximum Junction Temperature (Plastic Package). 150oC Maximum Storage Temperature Range. to 150oC Maximum Lead Temperature (Soldering 10s). 300oC

NOTES: JA is measured with the component mounted on an evaluation PC board in free air. 2. Short Circuit may be applied to ground or to either supply.

PARAMETER Input Offset Voltage Input Offset Current Input Current Large-Signal Voltage Gain

Common-Mode Rejection Ratio Common-Mode Input-Voltage Range Power-Supply Rejection Ratio Maximum Output Voltage


For Design Guidance, VSUPPLY = 25oC, Unless Otherwise Specified CA3160 SYMBOL TEST CONDITIONS 10k Across Terminals 4 and 5 or Terminals 4 and = 10M TYP CA3160A TYP UNITS pF V nV/Hz

Input Offset Voltage Adjustment Range Input Resistance Input Capacitance Equivalent Input Noise Voltage

PARAMETER Unity Gain Crossover Frequency Slew Rate Transient Response Rise and Fall Time Overshoot Settling Time For Design Guidance, VSUPPLY = 25oC, Unless Otherwise Specified (Continued) CA3160 SYMBOL 2k , (Voltage Follower) To <0.1%, VIN 2k , (Voltage Follower) TEST CONDITIONS TYP CA3160A TYP UNITS MHz V/s % s

PARAMETER Input Offset Voltage Input Offset Current Input Current Common-Mode Rejection Ratio Large Signal Voltage Gain

For Design Guidance, = 25oC, Unless Otherwise Specified CA3160 SYMBOL VIO IIO Il CMRR AOL = 5k TEST CONDITIONS TYP CA3160A TYP to UNITS pA dB kV/V V A V/V

Common-Mode Input Voltage Range Supply Current

NOTES: 4. Total supply voltage (for indicated voltage gains) = 15V with input terminals biased so that Terminal 6 potential is +7.5V above Terminal 4. 5. Total supply voltage (for indicated voltage gains) = 15V with output terminal driven to either supply rail.


Some Part number from the same manufacture Intersil Corporation
CA3160E 4MHz, Bimos Operational Amplifier With MOSFET Input/cmos Output
CA3161 BCD to Seven Segment Decoder/driver
CA3162 A/D Converters For 3-Digit Display
CA3162AE A/D Converter For 3-digit Display
CA3162E A/D Converters For 3-Digit Display
CA3165 Electronic Switching Circuit
CA3183 High-voltage Transistor Arrays
CA3189 FM if System
CA3193 1.2MHz, Bicmos Precision Operational Amplifiers
CA3194 Single Chip Pal Luminance/chroma Processor
CA3224E Automatic Picture Tube Bias Control Circuit
CA3227 High-frequency NPN Transistor Array For Low-power Applications at Frequencies up to 1.5GHz

ACS05K : Radiation Hardened Hex Inverter With Open Drain Outputs

CD4555BKMSR : Space Applications Radiation Hardened CMOS Dual Binary to 1 of 4 Decoder/demultiplexers

ISL83085EIB : 15kV ESD Protected, 5V, Full Fail-Safe, Fractional (1/8) Unit Load, RS-485/RS-422 Transceivers The ISL8308XE are BiCMOS, ESD protected, 5V powered, single transceivers that meet both the RS-485 and RS-422 standards for balanced communication. Each driver output, and receiver input, is protected ag

ISL9014AIRNJZ : ISL9014A is a high performance dual LDO capable of sourcing 300mA current from both outputs. The device has a low standby current and high-PSRR and is stable with output capacitance of 1μF to 10μF with ESR of up to 200mΩ. A reference bypass pin allows an external capacitor for adju

ISL6256AHAZ : Highly Integrated Battery Charger with Automatic Power Source Selector for Notebook Computers The ISL6256, ISL6256A is a highly integrated battery charger controller for Li-Ion/Li-Ion polymer batteries. High Efficiency is achieved by a synchronous buck topology and the use of a MOSFET, instead of a

X5043M8IZ : CPU Supervisor with 4K SPI Eeprom

X1288V14Z-4.5A : 2-wire RTC Real Time Clock/calendar/cpu Supervisor with Eeprom

ISL28233FUZ-T7A : 4.5mhz, Single and Dual Precision Rail-to-rail Input-output (rrio) Op Amps with Very Low Input Bias Current

ISL267817IUZ : 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 Specifications: Package Type: ROHS COMPLIANT, PLASTIC, MO-187AA, MSOP-8 ; Screening Level: Industrial ; Pins: 8 ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Sample Rate: 200 kSamples/Sec ; Input Voltage: -0.1000 to 2.5 volts

5962F0253402VZA : 2.25 V-26 V ADJUSTABLE NEGATIVE LDO REGULATOR, 1 V DROPOUT, CDFP28 Specifications: Regulator Type: Low Dropout ; Output Polarity: Negative ; Output Voltage Type: Adjustable / Variable ; Package Type: Other, CERAMIC, DFP-28 ; Life Cycle Stage: ACTIVE ; Output Voltage: 2.25 to 26 volts ; Dropout Voltage: 1 volts

Same catergory

AD828 : Dual, Low Power Video op Amp. Excellent Video Performance Differential Gain & Phase Error & 0.05 High Speed 130 MHz 3 dB Bandwidth V/ s Slew Rate 80 ns Settling Time to 0.01% Low Power 15 mA Max Power Supply Current High Output Drive Capability: 50 mA Minimum Output Current per Amplifier Ideal for Driving Back Terminated Cables Flexible Power Supply Specified for 5 V and 15 V Operation.

AD9300 : Multiplexers. 4 X 1 Wideband Video Multiplexer. 34 MHz Full Power Bandwidth 0.1 dB Gain Flatness to 8 MHz 72 dB Crosstalk Rejection @ 10 MHz 0.03 /0.01% Differential Phase/Gain Cascadable for Switch Matrices MIL-STD-883 Compliant Versions Available APPLICATIONS Video Routing Medical Imaging Electro Optics ECM Systems Radar Systems Data Acquisition The is a monolithic high speed video signal multiplexer.

AN6150 : Speech Network Circuit. The is an integrated circuit designed for telephone speech network. It has the basic function necessary to apply a sound signal onto the line and is applicable for various types of handsets. Wide operating voltage range to 11.5V Built-in amplifiers for "Dial Tone" and "DTMF" Amplifier output switchable. Each amplifier gain automatically changeable depending.

CHP1232 : HBT Single Supply Module, 1850-1910 MHZ. InGaP HBT Technology 6mm Square, 50 Ohm Power Module Single Positive Supply 35% Linear Power Added Efficiency +28.5 dBm Output Power (CDMA Mode) 30 dB Gain at Operating Output Power On-Board Power Down Mode Applications PCS Handsets PCS Infrastructure Wireless Local Loop Subscriber Units CDMA Handsets CDMA2K 1X Handsets The a 50 ohm matched, single.

CLC5802 : Dual Low-noise, Voltage Feedback op Amp. The is a dual op amp that offers a traditional voltage-feedback topology featuring unity-gain stability. Low noise and very low harmonic distortion combine to form a very wide dynamic-range op amp that operates within a power supply range to 12V. Each of the CLC5802's closely matched channels provides a 140MHz unity-gain bandwidth with a very low input.

FTS6504 : RF Distribution - Irig B. Superior IRIG B Signal Distribution High Channel Isolation Rack Mount or Bench top Ten Channel Output Distribution Compact & Light weight Daisy Chain For More Than 100 Outputs The DATUM 6504 Distribution Module is a ten channel, IRIG-B distribution amplifier packaged a 1U rack mount chassis. It is comprised of ten low phase noise RF amplifiers that.

KIA8256H : Bipolar Linear Integrated Circuit ( Three Audio Power Amplifier ).

LM239AQDREP : ti LM239A-EP, Military Enhanced Plastic Quad, General Purpose Differential Comparator.

LM4843 : Stereo 2w Audio Power Amplifiers With DC Volume Control. LM4843 Stereo 2W Audio Power Amplifiers with DC Volume Control The is a monolithic integrated circuit that provides DC volume control, and stereo bridged audio power amplifiers capable of producing 2W into 4 (Note 1) with less than 1.0% THD or 2.2W into 3 (Note 2) with less than 1.0% THD. Boomer audio integrated circuits were designed specifically.

MAX9000 : Low-Power, High-Speed, Single-supply op Amp Comparator Reference Ics. The MAX9000 family the combination of a highspeed operational amplifier, a 185ns comparator, and a precision 1.230V reference. These devices operate from a single to +5.5V supply and draw less than 500A of quiescent current. The MAX9001/MAX9004 feature a shutdown mode that reduces supply current to 2A and puts the outputs into a high-impedance state,.

MC3303 : Quad Operational. Output voltage can swing to GND or negative supply Wide power supply range; Single supply to 36V Dual supply to 18V Electrical characteristics similar to the KA741 Class AB output stage for minimal crossover distortion Short circuit protected output. The MC3303/MC3403 series is a monolithic Quad operational amplifier consisting of four independent.

TDA1313 : TDA1313; TDA1313T; Stereo Continuous Calibration DAC (CC-DAC). Objective File under Integrated Circuits, IC01 July 1993 4/8 oversampling (multiplexed/simultaneous input) possible Voltage output (capable of driving headphone) Space saving package or DIL16) Low power consumption Wide dynamic range (16-bit resolution) Continuous Calibration concept Easy application: single 5.5 V supply rail output voltage is proportional.

TIM5359-30L : Microwave Power GAAS Fet. MICROWAVE POWER GaAs FET Low Distortion Internally Matched Power GaAs FETs (C-Band) Low intermodulation distortion = -45 dBc = 34.5 dBm, - Single carrier level High power = 45 dBm at 5.3 GHz to 5.9 GHz High gain at 5.3 GHz to 5.9 GHz Broad band internally matched Hermetically sealed package RF Performance s (Ta 25 C) Characteristics Output Power at 1dB Compression.

U2510B-MT : All-band AM/FM Receiver And Audio Amplifier. The is an integrated bipolar one-chip AM/FM radio circuit. It contains an FM front end with preamplifier, FM IF and demodulator, a complete AM receiver, an AF amplifier and a mode switch for AM, FM and tape. This circuit is designed for clock radios and portable radio-cassette recorders. D Superior FM strong signal behavior by using RF AGC D Soft mute.

X9319 : Quad Digitally-controlled (XDCPTM) Potentiometer. Solid-state potentiometer 3-wire serial interface Terminal voltage, +10V 100 wiper tap points --Wiper position stored in nonvolatile memory and recalled on power-up 99 resistive elements --Temperature compensated --End to end resistance range 20% Low power CMOS --VCC = 5V --Active current, 3mA max. --Standby current, 1mA max. High reliability --Endurance,.

X9511 : Single 32 Tap Pushpot XDCP Push Button Interface Single Supply. Solid-state nonvolatile 16 wiper taps 3-wire up/down serial interface VCC = 2.7V and 5V Active current < 50A max. Standby current < 1A max. RTOTAL = 10K Packages: MSOP-8, SOIC The Xicor is a digitally controlled nonvolatile potentiometer designed to be used in trimmer applications. The pot consists of 15 equal resistor segments that connect.

MAX2056 : 800MHz to 1000MHz Variable-Gain Amplifier with Analog Gain Control The MAX2056 general-purpose, high-performance variable- gain amplifier (VGA) is designed to operate in the 800MHz to 1000MHz frequency range*. This device 15.5dB of gain, 4.5dB of noise figure, and an output 1dB compression point of 23.5dBm. The MAX2056 also provides an exceptionally.

OPA2301 : Low-Noise, High-Speed, 16-Bit Accurate CMOS Operational Amplifier The OPA300 and OPA301 series high-speed, voltage-feedback, CMOS operational amplifiers are designed for 16-bit resolution systems. The OPA300/OPA301 series are unity-gain stable and feature excellent settling and harmonic distortion s. Low power applications benefit from low quiescent.

MCP6071 : 110 A, High Precision Op Amps The MCP6071 operational amplifier (op amps) has a low input offset voltage (150 ?V, maximum) and rail-to-rail input and output operation. The MCP6071 is unity gain stable and has a gain bandwidth product of 1.2 MHz (typical). This device operates with a single supply voltage as low as 1.8V, while drawing low quiescent.

DS1553 : 64kB, Nonvolatile, Year-2000-Compliant Timekeeping RAM The DS1553 is a full-function, year-2000-compliant (Y2KC) real-time clock/calendar (RTC) with an RTC alarm, watchdog timer, power-on reset, battery monitor, and \"8k x 8 nonvolatile static RAM (NV SRAM).\" User access to all registers within the DS1553 is accomplished with a bytewide interface as shown.

0-C     D-L     M-R     S-Z