Details, datasheet, quote on part number: CMM0224-BD
CategoryRF & Microwaves => GaAs MMIC Chips
TitleGaAs MMIC Chips
DescriptionWideband Devices, 2 GHZ to 24 GHZ
DatasheetDownload CMM0224-BD datasheet


Features, Applications

Advanced Product Information April 2003 Features Small Size: x 92 mils High Gain Directly Cascadable Medium Power: +24 dBm Ion-Implanted Active Layers Silicon Nitride Passivation

Frequency Range Small Signal Gain Flatness Input/Output VSWR Power Output (@1 dB Gain Compression) Second Order Intercept Point Third Order Intercept Point Current

Die Attach: Eutectic die attach is recommended. For eutectic die attach: Preform: AuSn (80% Au, 20% Sn); Stage Temperature: 290C, 5C; Handling Tool: Tweezers; Time: 1 min or less. Wire Bonding: Wire Size: to 1.0 mil in diameter (prestressed); Thermocompression bonding is preferred over thermosonic bonding. For thermocompression bonding: Stage Temperature: 250C; Bond Tip Temperature: 150C; Bonding Tip Pressure: to 40 gms depending on size of wire.

Drain Voltage Drain Current Continuous Power Dissipation Channel Temperature Storage Temperature Mounting Temperature Input Power

Typical Scattering Parameters, = 25C (S-Parameters Include Bonding Wire Parasitics)
Freq (GHz) (dB) S11 (Mag) (Ang) (dB) S21 (Mag) (Ang) (dB) S12 (Mag) (Ang) (dB) S22 (Mag) (Ang)

The CMM-0224-BD is available in bare die and is shipped in Gel Pak. Package Part Number for Ordering CMM0224-BD Bare Die Optional Current Setting Resistor 532-001525-002

Celeritek reserves the right to make changes without further notice to any products herein. Celeritek makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Celeritek assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Celeritek does not convey any license under its patent rights nor the rights of others. Celeritek products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Celeritek product could create a situation where personal injury or death may occur. Should Buyer purchase or use Celeritek products for any such unintended or unauthorized application, Buyer shall indemnify and hold Celeritek and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Celeritek was negligent regarding the design or manufacture of the part. Celeritek is a registered trademark of Celeritek, Inc. Celeritek, Inc. is an Equal Opportunity/Affirmative Action Employer.

3236 Scott Boulevard, Santa Clara, California 95054 Phone: (408) 986-5060 Fax: (408) 986-5095


Some Part number from the same manufacture Celeritek
CMM0330 Cellular RF ic Mmic Power Amplifiers, 824-928 MHZ
CMM0335 GSM RF ic Power Amplifiers, 890-915 MHZ
CMM0336 Cellular RF ic Mmic Power Amplifiers, 824-928 MHZ
CMM1321 PCS RF ic Mmic Power Amps, 1.85-1.91 GHZ
CMM1335 GSM RF ic Power Amplifiers, 1.7-1.91 GHZ
CMM1430-KU ku Band Products, 13.75-14.5 GHZ
CMM1530 PCS RF ic Mmic Power Amps, 1.85-1.91 GHZ
CMM2030-BD Fiber Optic Driver Amplifier, 30 KHZ to 30 GHZ
CMM2032-BD Fiber Optic Driver Amplifier, 30 KHZ to 32 GHZ
CMM2301 Ism Band Mmic Power Amplifier, 2.3-2.5 GHZ
CMM2305 Cellular RF ic Mmic Power Amplifiers, 800-2700 MHZ
CMM2311 Ism Band RF ic Products, 800-2700 MHZ
CMM2321 Ism Band RF ic Products, 2.4-2.5 GHZ
CMM3020-BD Fiber Optic Driver Amplifier, 20 KHz-20 GHZ

CHP0205-QM-000T : Module Cellular Ingap HBT Amplifier, 824-849 MHZ

CHP0230-PM : HBT Single Supply Module, 824-849 MHZ

CMM2306 : Cellular RF ic Mmic Power Amplifiers, 800-2700 MHZ

NE685M33 : LOW NOISE: NF = 1.5 dB TYP. @ VCE = 3 V, IC = 3 mA, f = 2 GHz INSERTION POWER GAIN: |S21e|2 = 11 dB TYP. @ VCE = 3 V, IC = 10 mA, f = 2 GHz 3-PIN SUPER LEAD-LESS MINIMOLD (M33) PACKAGE

NESG3031M14-T3-A : NEC's NPN SiGe High Frequency Transistor THE DEVICE IS AN IDEAL CHOICE FOR LOW NOISE, HIGH-GAIN AMPLIFICATION: NF = 0.95 dB TYP., Ga = 10.0 dB TYP. @ VCE = 2 V, IC = 6 mA, f = 5.2 GHz NF = 1.1 dB TYP., Ga = 9.5 dB TYP. @ VCE = 2 V, IC = 6 mA, f = 5.8 GHz MAXIMUM STABLE POWER GAIN: MSG = 15.0 d

UPD5713TK-E2-A : Wide Band SPDT Switch The uPD5713TK is a CMOS MMIC for wide-band SPDT Single Pole Double Throw which were designed for mobile communications, wireless communications and another general-purpose RF switching application. This device can operate frequency from 0.05GHz to 2.5GHz,, having the low in

MC7834KC : NEC's 870 MHz GaAs CATV 20 dB Push-Pull Amplifier (Higher Current Version For Higher Distortion Performance) NEC's MC-7834-KC is a GaAs Multi-Chip Module designed for use as input stages in CATV applications up to 870 MHz. Because this unit is a GaAs device, it has low distortion, low noise figur

PS7142-1C : 8 PIN DIP 400 V Breakdown Voltage, Transfer Type 2-CH Optical Coupler MOSFET The PS7142-1C and PS7142L-1C are transfer type solid state relays containing normally open (N.O.) contact and normally close (N.C.) contact on output side. They are suitable for analog signal control because of their low

PS7200H-1A-E4 : 4 PIN SOP, 2.2 ohms Low On-State Resistance 1-CH Optical Coupled MOSFET The PS7200H-1A is a low on-state capacitance solid state relay containing a GaAs LED on the light emitting side (input side) and MOS FETs on the output side. It is suitable for high-frequency signal control, due to its low C

PS7200U-1A-F4 : NEC's 4-PIN SOP Low Off-State Leakage Current, 1-CH Optical Coupled MOS FET NEC's PS7200U-1A is a low output capacitance solid state relay containing GaAs LEDs on the light emitting side (input side) and MOS FETs on the output side.

PS7206-1A : 4 PIN SOP, 0.6 ohms Low On-State Resistance 600 mA Continuous Load Current 1-CH Optical Coupled MOSFET The PS7206-1A is a low on-state resistance solid state relay containing GaAs LEDs on the light emitting side (input side) and MOS FETs on the output side. It is suitable for PLC, etc. because of

PS7431-1A : 4 PIN SOP High Isolation Voltage 3000 V.r.m.s. 1-CH Optical Coupled MOSFET The PS7431-1A is a solid state relay containing GaAs a LED on the light emitting side (input side) and normally open (N.O.) contact MOS FETs on the output side. It is suitable for analog signal control because of its low of

Same catergory

855679 : = Filter - Broadband Access ;; Frequency (MHz) = 80 ;; Bandwidth (MHz) = 8 ;; Insertion Loss (dB) = 14.0 Max ;; Modes of Operation = se ;; Package (mm) = 13.3 X 6.5.

855739 : = Filter - STD 70 High-selectivity ;; Frequency (MHz) = 70 ;; Bandwidth (MHz) = 2 ;; Insertion Loss (dB) = 24.25 Max ;; Modes of Operation = se ;; Package (mm) = 19.0 X 6.5.

AA239-12 : Digital Attenuator. GAAS ic 3 Bit Digital Attenuator 4 DB. Attenuation 4 dB Steps 28 dB with High Accuracy Single Positive Control Voltage for Each Bit +5 V Operation Small Low Cost SOIC-8 Plastic Package The a 3 bit, single positive control, 4 dB step GaAs IC FET digital attenuator in a low cost SOIC-8 plastic package. For positive operation external DC blocking capacitors are required on all RF ports. The AA239-12.

AS004R2-11 : GAAS ic SPDT Low Loss Switch. s Low DC Power Consumption s Reflective, Short s 8 Lead Hermetic Surface Mount Package s Capable of Meeting MIL-STD Requirements6 The AS004R2-11 SPDT reflective switch operates from DC4 GHz. These devices are useful as modulators and switches in high reliability and commercial applications. Parameter Switching Characteristics Condition Rise, Fall or 90/10%.

CXA3627N : All Band Tuner ic With On-chip PLL. The is a monolithic TV tuner IC which integrates local oscillator and mixer circuits for VHF band, local oscillator and mixer circuits for UHF band, an IF amplifier and a tuning PLL onto a single chip, enabling further miniaturization of the tuner. Low power consumption (5V, 63mA typ.) Low noise figure, low distortion characteristics High gain/low gain.

ETK4-1T :  E-Series SMT RF 4:1 Transformer 8 - 750 MHZ. M/A-COM's 4:1 RF transformer in a low-cost, surface mount package. Ideally suited for high volume cellular and wireless applications. Typical applications include single to balanced mode conversion and impedance matching. Note: Mean and sigma calculated from average loss f L. Parameter RF Power DC Current Operating/Storage Temp. Absolute Maximum to +85C.

HMC273MS10G : 5-Bit, 1 to 31dB Range, +48dBm Input IP3, 0.7 to 3.7 Ghzthe HMC273MS10G is a Broadband 5 - Bit Positivecontrol GAAS ic Digital Attenuator in a 10 Lead Msopplastic Package. Covering 0.7 to 3.7 Ghz, The Insertionloss is Typically Less Than 2 DB. The Attenuatorbit Values Are 1 (LSB), 2, 4, 8, And 16 DB For a Totalattenuation of 31 DB. Accuracy is Excellent.

HMC321LP4 : SP8T. Broadband Performance: - 8.0 GHz High Isolation: >30 dB@ 6 GHz Low Insertion Loss: 2.5 dB@ 6 GHz Integrated Positve Supply 3:8 TTL Decoder 1 mm SMT Package GaAs MMIC SP8T NON-REFLECTIVE POSITIVE CONTROL SWITCH, DC* - 8.0 GHz Typical Applications This switch is suitable for usage - 8.0 GHz or 75-Ohm systems: Broadband Fiber Optics Switched Filter.

HMC346 : Analog Vva. Wide Bandwidth: - 20 GHz Low Phase Shift vs. Attenuation 32 dB Attenuation Range Die Size: 0.1 mm Typical Applications The HMC346 die is an absorptive Voltage Variable Attenuator (VVA) operating from - 20 GHz. It an on-chip reference attenuator for use with an external op-amp to provide simple single voltage attenuation control, to -3V. The device is ideal.

M83M83C : Triple-balanced Mixer. TRIPLE-BALANCED MIXER TO 18 GHz TO 18 GHz TO 5 GHz LO DRIVE +13 dBm (nominal) WIDE BANDWIDTH SSB Conversion Loss & SSB Noise Figure (max.) to 13 GHz, to 13 GHz, to 2 GHz to 16 GHz, to 18 GHz, to 4 GHz to 18 GHz, to 18 GHz, to 5 GHz fI = Isolation (min.) to 3 GHz to 18 GHz to 18 GHz 1 dB Conversion Compression @ +13 dBm fL @ Input = 6 GHz @ -3 dBm = 3.01.

MACPES0050 :  E-Series SMT 75 Ohm 20 DB Coupler 5 - 1000 MHZ. Low Intermod Distortion Coupling 20db Typical Surface Mount Tape and Reel Packaging available M/A-COM's is a high performance 75 Ohm Coupler, a SM-55 low cost, surface mount package. Ideally suited for high volume CATV applications. Input Return Loss Output Return Loss Please Note that the photograph above indicates package shape only, unit may be wired.

MASWSS0070 :  GaAs Broadband SPDT Switch, DC - 6.0 GHZ. 802.11a + b/g Dual Band Applications Broadband Performance: - 6.0 GHz Low Insertion Loss: at 6.0 GHz High Isolation: 25 dB Typical Low Cost 3 mm FQFP-N 12 Lead Package Fast Switching Speed: 0.5 m GaAs PHEMT Process M/A-COM's is a broadband GaAs PHEMT MMIC SPDT switch in a low cost 3 mm FQFP-N 12 lead package (JEDEC). The MASWSS0070 is ideally suited.

RFP-40N50TPR : = Terminations ;; Size LXWXH = 0.25" X 0.515" X 0.15" ;; Packaging = Flanged ;; Frequency MHZ = 0-4000 ;; Power Handling Watts = 40.

SWX-01 : = Pin Diode Switches, High ISOlation-surface Mount ;; Freq. Range = 0.2-2.4 GHZ.

TDA6131XS : Universal Mixer.

TRF3040PHP : Cellular / PCS. ti TRF3040, Modulator/synthesizer. 2-GHz Main Synthesizer, Which Incorporates a Dual-Mode 32/33 and 64/65 Prescaler for Fractional-N Operation 200-MHz Auxiliary Synthesizer, Which Incorporates an 8/9 Prescaler Separate Supply Terminals for Main and Auxiliary Charge Pumps Internal Compensation for Fractional Spurs Low Phase Noise Normal and Integral Charge Pump Outputs Fully Programmable.

AD8312 : 50 MHz to 2.7 GHz, 45 dB RF Log Detector The AD8312 is a complete low cost subsystem for the measurement of RF signals in the frequency range of 100 MHz to 2.7 GHz, with a typical dynamic range of 45 dB, intended for use in a wide variety of cellular handsets and other wireless devices. It provides a wider dynamic range and better accuracy than possible.

ADV7510 : Deep Color HDMI 1.3 Transmitter With CEC The ADV7510 is a 225 MHz High Definition Multimedia Interface (HDMI) transmitter, which is ideal for home entertainment products including DVD players/recorders, digital set top boxes, A/V receivers, gaming consoles, and PCs. The digital video interface contains an HDMI and a DVI v.1.0-compatible transmitter,.

SKY77605 : Multiband Multimode Power Amplifier Module For Quad-Band GSM / EDGE And Broadband (Bands I, II, V, VIII) WCDMA / HSDPA / HSUPA / HSPA+ Handsets Skyworks SKY77605 is a hybrid multimode, multiband Power Amplifier Module (PAM) that supports 2.5G and 3G handsets, and operates efficiently in GSM, EGPRS, EDGE and WCDMA modes. The PAM consists of a GSM800/EGSM900.

0-C     D-L     M-R     S-Z